低合金高强度钢的微观组织和疲劳裂纹扩展行为

用透射电镜观察了３０ＣｒＭｎＳｉＮｉ２Ａ钢等温的微观组织，疲劳裂纹扩展行为、裂纹尖端塑性区和位错结构，结果表明，等温状态组织由马氏体和贝氏体组成。在一个奥氏体晶粒内一般存在四个板条领域、裂纹尖端的塑性区内存在主位错带，疲劳断裂的基本组织单元为板条晶或板条束。裂纹遇到板条束界时方向发生较大偏斜。     

Prediction of High-Temperature Long-Term Strength for Damaged Structures

A method is proposed for analytical estimation of the high-temperature long-term strength of structures with material discontinuities, which are stress raisers. We consider the processes involving the formation of diffusion pores. Diffusion processes in metals are strongly enhanced with increasing temperature and stresses.     

PP/EPDM/CaCO_3三元共混体系的脆韧转变研究

采用扫描电镜和材料力学性能试验方法研究了ＰＰ／ＥＰＤＭ／ＣａＣＯ３三元体系中ＣａＣＯ３的表面处理与其材料的缺口冲击韧性及产生脆韧转变现象之间的关系。实验结果及分析表明：体系中分散相颗粒周围向ＰＰ基体扩散、渗透或与之共结晶的ＥＰＤＭ部分是增韧ＰＰ的有效成分；较好的表面处理条件下，体系中加入较少量的ＥＰＤＭ即可使材料缺口冲击韧性和拉伸模量值同时达到较好水平。     

拉伸试样弯曲度对屈服强度测试值的影响

分析了输送管管体横向拉伸试样弯曲度对屈服强度测试值的影响,从理论上初步阐明了管体横向拉伸试样的弯曲会引起屈服强度测试值的降低,并提出在相关的标准中应对管体横向试样的展平程度作出规定.     

预测井眼稳定性的力学化学耦合方法

在井眼力学稳定性评价的基础上，将硬脆性页岩水化后岩石强度等参数的变化规律用于页岩水化前后坍塌压力变化的对比分析，结果表明，地层坍塌压力当量密度随页岩水化程度的增加逐渐升高。给出了预测井眼稳定性的力学化学耦合方法，并将该方法应用于现场生产中，取得了较好的预测效果     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

几种高强度钢腐蚀疲劳裂纹扩展行为的研究

本文研究了ＧＣ－４，３０ＣｒＭｎＳｉＮｉ２Ａ和３００Ｍ超高强钢的腐蚀疲劳裂纹扩展行为。考虑了环境，热处理制度，应力比和频率对裂纹扩展的影响。研究结果表明：腐蚀环境和热处理制度对疲劳裂纹扩展有显著影响。在侵蚀性环境中随频率降低，裂纹扩展大幅度上升，随应力比提高，环境影响加剧。利用扫描电镜对试样断口形貌进行了分析，并讨论了高强钢的腐蚀疲劳机理。     

用微脱胶技术表征芳纶纤维材料界面强度

采用微脱胶原位技术表征了Ａｐｍｏｃ，芳纶－Ⅱ纤维复合材料界面结合强度。     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

The mechanics of compressive kinking in unidirectional fiber reinforced ductile matrix composites

Three distinct stages of kink band formation and propagation exist in ductile matrix composites subjected to compressive loading. These stages are called incipient kinking, transient kinking and kink band broadening. Each stage involves a different deformation mode. The mechanics governing each stage are discussed. Incipient kinking, where the peak load is attained, and kink band broadening, where the load attains a steady-state, are important in structural design. Two design philosophies are presented. References to pertinent literature are made throughout.