Influence of base resistance on extracting thermal resistance for SiGe HBTs

In this article, the influence of base resistance on extracting thermal resistance for SiGe heterojunction bipolar transistors is studied and an improved approach for determining the junction temperature and thermal resistance is presented. The proposed method for extracting thermal resistance is based on the temperature sensitivity of the base–emitter (B–E) voltage when the device is biased with a fixed emitter current density. This approach not only takes into account the self‐heating during the different ambient temperature measurement but also revises the empirical equation of B–E voltage due to the influence of base resistance during the power dissipation increment measurement. Results are obtained for devices with different emitter lengths and fingers. Compared with the conventional method, the thermal resistance is about up to 15% improvement for the device with 0.3 × 1.9 μm² emitter area and 13.8% for the device with 0.3 × 13.9 μm² emitter area. The accurate thermal resistance implemented in HICUM model has resulted in better fit for transistor output characteristics. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2012.     

耐腐蚀摩托艇ADC12-0.5La铝合金微观组织及制备

为改善ADC12铝合金的耐腐蚀性能,通过超声熔铸法制备ADC12-0.5La铝合金,并利用光学显微镜、扫描电镜、能谱分析仪、硬度计、浸泡腐蚀试验和电化学工作站研究了T6热处理和稀土La改性对ADC12铝合金的微观组织、硬度和耐腐蚀性能的影响。结果表明,T6态ADC12-0.5La铝合金微观组织明显细化,α-Al尺寸减小,形貌变圆整,共晶Si相和AlFeMnSi相细化为短棒状。相比于ADC12铝合金,T6态ADC12-0.5La铝合金硬度达到117.7HV,提高了26.8%,腐蚀电流密度降低了10.7%,腐蚀电位上升了64.4%,腐蚀速率降低了54.4%,腐蚀表面平坦且光滑,表现为较轻微的晶间腐蚀。T6态ADC12-0.5La铝合金提高了腐蚀电位,Al-La-Cu稀土相阻碍了电子移动,铝合金的耐腐蚀性能得到大幅度提高。     

Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

FORMATION OF MANGANESE SILICIDE THIN FILMS BY SOLID PHASE REACTION

1. IntroductionThe transition metal silicides have attraeted much attention because of their potentialapplicatiOIl in very large scale integration (VLSI) de.ice[1]. Near-noble metal silicides canbe used as Schottky al1d ohn1ic col1tacts in silicon-based d…     

电感电容损耗电阻的讨论

通过对电容电感阻抗的测量，发现实验值偏离理论值。定性地分析了误差的来源，得出的结论是电感电容内部的损耗电阻随着频率的变化而变化，变化方向相反而并非相同。     

提高高铬白口铸铁磨球冲击抗力的技术关键

当高铬白口铸铁含铬量为18%～28%,Cr/C值是8￣9,铸铁的显微组织是回火马氏体 少量残余奥氏体(<5%) M7C3碳化物,则磨球具有高的冲击韧性和断裂韧性K1C,具有高的冲击抗力,表现出低的冲击剥落量。     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

利用C++Builder对处理ESCR数据方法的改进

介绍一种利用C＋＋Builder编程工具自动处理聚乙烯环境应力开裂(ESCR)试验数据的方法。此方法利用计算机简化试验数据的处理过程,消除标准试验方法中作图法所引入的人为误差,并可以大幅度缩短试验时间。     

成形压力对氧化铝瓷球性能的影响

本文以不同的压力等静压成形瓷球，研究了成形压力对瓷球烧结温度、密度及耐磨性的影响。结果表明：在本研究系统内随着压力的增加瓷球的烧结温度下降，烧成温度范围拓宽。采用150MPa成形的瓷球密度最大且耐磨性最好。