碳/环氧复合材料的冲击拉伸

该文研究了T300碳纤维单向增强的环氧复合材料,在应变率从10~(-3)/s到10~3/s范围内的冲击拉伸行为.通过对实验数据进行拟合,得出该范围内材料对应变率具有弱的敏感性,表现在破坏强度及破坏应变随应变率增加不显著变化,平均模量几乎不受应变率的影响.分析了试件的几何尺寸效应,讨论了应力波作用对破坏形态的影响以及实验中观察到的拔出现象.从应变率在10~2～10~3/s附近材料行为某些非确定性,指出在更宽范围内了解其性能的必要性.     

特种钢用结晶器铜管破裂原因分析

通过对某特钢厂破裂的结晶器铜管进行金相实验、扫描电镜和能谱分析,并结合结晶器的生产、使用及失效过程情况,综合受力分析,认为铜管破裂原因主要是环境介质硫渗入形成硫化物,在拉应力作用下,裂纹沿脆性质点扩展导致的破坏。     

Delaminations at the free edge of a composite laminate

The concept of a fracture process zone where damage takes place is used to analyse the delaminations at the free edges of angle ply laminates under uniaxial tension. The use of a fracture process zone removes the singularity in the interlaminar stresses and enables the initiation and growth of delaminations to be modelled for a perfect laminate without any assumed prior defects. Two different models for the stress displacement relationship in the fracture process zone are examined: a constant stress up to critical displacement and a linear relationship. Finite element analysis shows that there is little difference in the predictions obtained from the two models. An approximate analysis is presented for the constant stress stress-displacement model which is shown to agree with a finite element solution and experimental data. Hence it is argued that the approximate method using a constant stress model for the fracture process zone is sufficient for accurate prediction of delaminations.     

���׸ߵ����ѷ��ݻ�����ԭʼ�������㷽��̽��

本文把与井简直接连通的大裂缝及井筒定义为“裂缝—井筒系统”,通过气体状态方程的变换和续流总量的计算,探索出井底大裂缝的容积及其储量的计算方法。     

Magnetic and mössbauer studies on ductile Fe-Cr-Co permanent magnet alloys

Iron-chromium-cobalt alloys possess attractive magnetic properties combined with good formability and hence are identified as technologically important magnetic materials. Alloys with compositions Fe-28·9 Cr-15·6 Co and Fe-28·4 Cr-20·1Co (weight percent) have been studied. Heat-treatment parameters during thermomagnetic treatment viz temperature, time and external magnetic field were optimized with reference to magnetic properties. The fully treated anisotropic alloys develop remanence=11·5–12·0 kilo Gauss, coercivity=600–650 Oersted and energy product=4–4·5 million Gauss Oersted. Electron microscopic and Mössbauer spectroscopic techniques were used to identify the original and transformed phases. During the various stages of the development of the alloy, the changes in mechanical hardness were correlated with magnetic hardness.     

冶炼工艺对GH871合金涡轮盘韧性的影响

研究了AIM ESR和VIM ESR两种冶炼工艺对GH871合金涡轮盘三种韧性指标的影响,结果表明:冶炼工艺对该合金在室温、650℃拉伸和缺口冲击韧性影响较小,采用VIM ESR冶炼工艺可以显著提高GH871合金在700℃拉伸韧性和I型裂纹平面应变的断裂韧性。     

用微量元素涂料改善球铁件热节组织的试验研究

对RE、Tc、Bi、Sb等微量元素以涂料形式对球铁件厚大热节部位进行微合金化,以改善其组织的可能性进行了试验研究,结果表明:多元微量元素涂料可有效地消除碎块状石墨,提高球化率,改善球铁组织,涂料层厚度影响微合金化程度而应严格控制,该工艺具有简便。无炉料污染、可代替冷铁以确保复杂铸件组织均一等优点。     

基于孔隙压力黏结单元的准脆性材料水力劈裂模拟

传统数值方法对水力劈裂的模拟一般采用预设裂缝扩展路径,且将水流作用等效为压力荷载,难以反映裂缝渗流-开裂耦合效应. 采用自编程Python脚本程序批量插入孔隙压力黏结单元,考虑裂缝渗流-开裂耦合作用模拟准脆性材料水力劈裂随机扩展全过程. 在对经典理论模型及试验结果模拟验证的基础上,开展含多裂缝均质模型的水力劈裂全过程分析,并进一步建立混凝土细观尺度水力劈裂模型,分析骨料、界面过渡区和基体渗透性对混凝土劈裂全过程的影响. 结果表明,本研究模型可以有效模拟准脆性材料水力劈裂失效过程,准脆性材料多缝开裂过程伴随微裂缝的分叉扩展而非光滑的裂缝扩展路径,骨料及界面过渡区影响劈裂扩展路径造成裂缝分叉出现,混凝土基体的渗透性对其抵抗水力劈裂不利并影响失效软化过程.     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

Crack initiation and propagation induced by inclusions in a nickel-base P/M superalloy under fatigue load

1 IntroductionRecently the key components in advanced aircraftengines are widely made of nickel-base P/M super-alloy. However, non-metallic inclusions are intro-duced into this material during powder metallurgyprocessing. In industry, although many method…