车载制氧机加装预冷装置的研究与实现

航空兵部队地面保障装备之一的车载移动式制氧机，采用封闭循环水冷却，由于受到使用条件的限制，多数情况下冷却效果不尽理想，加装蒸汽压缩预冷装置，即可较好地了和低冷却系统温度，提高制冷量和整机使用寿命，又可满足整车机动性，动力等技术要求。     

浓缩大豆磷脂制取工艺及设备的研究

对水化油脚采用新工艺和新设备制取浓缩大豆磷脂，并对制取浓缩大豆磷脂的影响因素进行分析和优化，得到了制取浓缩大豆磷脂新工艺和最佳工艺参数。     

钢管减阻型内涂层生产工艺及设备

介绍了钢管减阻型内涂层技术的生产工艺和主要设备，给出了内涂层生产线典型的工艺布置，并对主要设备的组成及工作原理进行了介绍。     

岩石工程力学特性参数测定装置设计

岩石工程力学特性参数测定装置实现了对试验载荷的恒速率加载 ,可对压模的吃深和试验载荷进行连续记录 ,记录的数据可实时显示及处理 ,且动态显示试验岩石的特性曲线 (试验载荷—轴向应变 )。该装置体积小、可移动性强 ,且能一机多用。文章详细阐述该装置机械结构、电路和系统软件的设计等     

穿透裂纹和表面半椭圆裂纹模型的失效评定曲线比较

针对弹塑性材料裂纹管道的J积分计算建立了等效穿透裂纹和表面半椭圆裂纹2种有限元模型。在等效穿透裂纹模型中应用了1／4节点单元，在表面裂纹模型中采用了线弹簧单元。用这2种模型计算J积分，分别对3个实际含裂纹管段建立了失效评定曲线。比较了2种模型的失效评定曲线和R6通用曲线的差别，指出穿透裂纹模型偏于保守，建议在油气管道断裂的工程评定中采用半椭圆表面裂纹模型。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

催化裂化再生系统设备应力腐蚀开裂成因分析及解决对策

通过对催化裂化装置再生系统设备裂纹断口分析 ,以及对再生烟气的组分、冷凝水酸度及露点等的分析及对设备焊接残余应力测试 ,阐明了设备应力腐蚀开裂发生的原因 ,指出了富氧操作、高露点温度和高应力水平对再生系统设备应力腐蚀的影响作用 ,并重点提出了解决和防止应力腐蚀开裂的一系列有效措施和部分应用情况     

精密扇形扫描稳速控制

在扇形扫描中，马达稳速的控制是通过相位补偿实现的。本文提出一种新的稳速控制方法、相位补偿控制，并介绍了相位补偿电路的设计。     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

中国测井装备研制及有关发展思路的建议

中国的测井装备研究取得了较大进展，将在近期推出成像测井系统和高可行测井系统。中国专有的聚焦型激发极化电位测民在积极研制之中。提出了对几项准备研制工作的方法，并对21世纪初中国测井装备的发展思路提出了建议，提出应将测井装备研制列为当前测井研究的中心任务，应加强测井装备研制的系统性和开放性。