400kt／a硫铁矿制酸装置挖潜扩能改造

介绍400 k t/a硫铁矿制酸装置的挖潜改造。通过调整工艺技术指标,增加少量设备和催化剂,将硫酸装置的生产能力从400 k t/a提高到450 k t/a,改造后各项技术经济指标均达到要求,2005年第1季度实现利润1 479万元,取得了明显的经济效益。     

Thermal Expansion of Solid Solutions in the ZrTiO4—In2O3—M2O5 (M = Sb, Ta) System

Axial and dilatometric thermal expansions and phase transformations were studied for solid solutions having the α-PbO₂ structure in the ZrTiO₄—In₂O₃—M₂O₅ (M = Sb, Ta) system with nominal formulas of Zr _x Ti _y In _z Sb _z O₄ and Zr _x Ti _y In _z Ta _z O₄ where x + y + 2 z = 2. With increased substitution of z , the cell volume increased, the difference in the b parameters at room temperature between those quenched from 1400° and 1000°C decreased, and the thermal expansion decreased. The axial thermal expansion of ZrTi _y In _z · Ta _z O₄ with z = 0.3 was almost identical with that of HfTiO₄, and those with z = 0.4 and z = 0.45 were smaller than that of HfTiO₄. Unit-cell volumes of these compound were compared with those of single oxides to make it clear that the unit-cell volume of ZrTiO₄ was small anomalously and to distinguish the normal and abnormal substitution systems. These results were explained by the working hypothesis proposed for these compounds.     

板壳式换热器设置膨胀节的判定

介绍板壳式换热器的主要特点和应用。当壳体与板束温差较大时,笔者通过对产品开发的生产实践,提出解决板壳式换热器要否设置膨胀节的类似判定方法。     

不同氧磷比对磷酸盐包边玻璃性质的影响规律

包边技术是提高大尺寸激光玻璃饱和增益系数的关键技术.采用传统的方法熔制玻璃,研究了P2O5含量对P2O5-Al2O3-B2O3-CuCl-Na2O-ZnO磷酸盐包边玻璃的折射率、热膨胀系数、玻璃转变温度、膨胀软化温度以及化学稳定性的影响.结果表明:当P2O5的摩尔分数为60%左右,玻璃样品具有最高的折射率(1.5220)、最低的玻璃转变温度(352.4℃)、较好的化学稳定性[0.52mg/(cm2·d)]和适宜的热膨胀系数(128.427×10-7/℃),是用作钕磷酸盐激光玻璃硬包边的理想材料.     

蜂窝式构件长细比的计算方法

为了进一步研究蜂窝构件稳定承载性能,以现有长细比计算理论为基础,结合蜂窝构件的受力机理和界面特性,提出了蜂窝构件长细比计算中相关参数的计算方法．同时,结合理论推导和数值分析结果,提出了蜂窝构件换算长细比建议计算公式．     

Precipitation and stability of reversed austenite in 9Ni steel

A new method was used to analyze the factors affecting the precipitation of reversed austenite during tempering. The samples were kept at various tempering temperatures for 10 min and their length changes were recorded. Then, the precipitation of reversed austenite which led to the length reduction was shown by thermal expansion curves. The results show that the effects of process parameters on the precipitation of reversed austenite can be determined more accurately by this method than by X-ray diffraction...     

Numerical investigation on bowed blades of Iarge meridional expansion Turbine

To improve the performance of the Turbofan engine,several measures should be considered during design process.Such measures,relating to aerodynamic characteristic design,include the maximum enthalpy per stage,the shortest axial length,the minimum blade rows and the highest efficient in design and off design condition.To satisfy theses design characters,the meridian geometry of the engine will he excurvature at a high degree transition part between HP and LP turbines.The study is to investigate the effect of blade bowing on flow loss at blade tip and root of the type of turbine.Such turbine,tending towards separation,with severe secondary flow at the tip and strong radial flow at exit,was simulated by the 3D N-S solver Numerea,and there were several different stacking line bowing schemes in all.The results show that tip negative bowing and root positive bowing is able to weaken radial flow,consequently reduce the flow loss at the tip and root.     

郑州地区粉土承载力确定方法的探讨

结合郑州地区典型岩土工程勘察实例,分析了以往采用理论公式计算法、参数查表法、静力触探参数计算法和载荷试验法等粉土承载力确定方法,探讨其中所存在的局限性。粉土承载力与原位测试值呈近似线性关系,而与土工试验参数相关性相对较差。提出了用原位测试法如标准贯入（SPT）和静力触探（CPT）等确定郑州地区粉土承载力的地域性经验公式。     

带积分边界条件的二阶微分方程三个正解的存在性

运用不动点定理,研究了一类带积分边界条件的二阶微分方程三个正解的存在性．推广了以前的结果．     

Experimental Study on the Expansion Uniformity of Armature

A measurement system has been developed based on high-precision printed probes in printed circuit board (PCB) and steep rising-time probe adapters,which can be applied to study the expansion uniformity of armature in a helical magnetic flux compression generator (HFCG).The influences of wall thickness and initiation position on the expansion uniformity of armature in HFCG were experimentally investigated.The results show that the armature with thinner wall thickness will easily rupture due to the high pressure of detonation products inside,the armature with larger wall thickness will easily crack due to the tensile stress on the outer surface of the wall,the influence of the end effect on the expansion uniformity can be ignored if the distance between the first group of probe and the initiation point is more than 3 times the armature diameter.