SJ—YⅡ—5型高爆速高威力水胶炸药的研制

文章简要分析了我国目前在中硬岩石爆破中工业炸药的使用情况，介绍了山西兴安化学材料厂新研制的一种适用于硬岩爆破的高爆速、高威力水胶炸药新品种，对其性能、爆破效果、经济实用性和安全性等进行了阐述。     

带隔板底水油藏油井临界产量计算公式

本给出了带隔板底水油藏油井的监界产量计算公式，它适用于所有带隔板底水油藏的油井。     

位山引黄灌区泥沙淤积原因及处理对策

位山灌区是黄河下游大型引黄灌区 ,渠系泥沙淤积严重 ,泥沙处理困难。通过采用远距离输沙、集中处理沉沙区泥沙、分散沉沙和节水减淤等技术措施 ,减少了渠系的泥沙淤积。对清淤产生的泥沙 ,采取综合开发利用的技术和管理措施 ,取得了比较可靠的效果。     

Effects of hydrolysis on the physical properties of short glass-fibre reinforced poly(ethylene terephthalate)

The mechanical fracture strength and toughness of short-fibre composites, injection moulded from compounds of poly(ethylene terephthalate) (PET) containing 10 and 30% (by weight) (w/o) glass, have been investigated and the dependence upon matrix hydrolytic stability determined. Mouldings have been characterised by several physical techniques to evaluate molecular weight, degradation rates, crystallinity and morphology, whilst time-dependent gravimetric data were derived to quantify sorption kinetics and allow comparisons with theoretical reaction rates to be made. During melt processing, PET is hydrolysed extremely rapidly by traces of moisture (<0.02w/o). yet the inherent strength of moulded composites declines significantly only below an apparently critical molecular weight. However, on long-term humid ageing in hot water, impact behaviour especially is rendered more complex by simultaneous crystallisation, molecular reorder and losses of interfacial bond strength.     

舰船水声隐身技术(二)

本文探讨了水声隐身性能对舰船战技术性能的影响 ,舰船水噪声的主要噪声源、水噪声的治理措施及其展望。     

Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

环境敏感因素对电站正常蓄水位选择的影响

卜寺沟水电站预可阶段正常蓄水位是考虑规划成果、地形、地质务件、梯级衔接、水库淹没、筑坝技术、水能资源利用等因素综合初选的.从理论角度分析,水库淹没时水库内寺庙的影响,按全部淹没进行经济补偿处理代价较小;其社会环境敏感因素对正常蓄水位的选择不应起决定性作用.但是,考虑到少数民族群众、僧侣和地方政府的要求,适当降低正常蓄水位,以减少对扎西日岗寺庙的影响,将带来较积极的社会影响.     

注射成形Fe-50%Ni软磁合金的研究

Fe-50 %Ni合金是一种典型的高磁导率和低矫顽力的软磁材料,有着广阔的应用前景.本次实验采用注射成形方法制取Fe-50 %Ni,研究了在注射成形工艺中烧结工艺对最终产品性能及微观组织的影响,并分析了影响产品磁性能的一些主要因素.实验表明,烧结温度的提高和烧结时间的延长能够较好改善产品的力学性能;密度是影响产品磁性能的主要因素,杂质(主要指(C、O、N)的含量和晶粒尺寸对剩磁、磁导率和矫顽力也有较大的影响;通过注射成形方法制取的Fe-50 %Ni,其性能要优于采用传统粉末冶金方法制造的Fe-50 %Ni.     

调整水量法(代用法)测定水泥标准稠度用水量方法的改进

结合兰州市的水泥标准稠度用水量方法测定 (代用法 )的实例 ,分析代用法测定标准稠度用水量的缺点 ,并对此方法提出了一些改进措施