Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

从生产角度论述空分设备“有效产品成本”

引入空分设备“有效产品成本”概念，以气体成本算法和液体成本算法对空分设备正常产品单位成本和有效产品单位成本进行了比较，举例计算了液化装置的产品成本，提出利用“有效产品成本”概念来组织空分设备生产。     

燃料性质对加热炉腐蚀结焦的影响及其防治

从加热炉燃料变化情况入手 ,分析了加热炉目前存在的炉管结垢 ,预热器烟气露点腐蚀以及炉体腐蚀等问题。从机理上进行了探讨 ,从而提出了原油脱金属、燃料气脱硫、燃料油优化、化学除垢以及预热器改造等防护措施。     

马鞍山煤矿瓦斯地质理论在防突工作中的应用

总结了实际工作中防突管理的经验和问题 ,探讨了科学理论与具体实际的有机结合与统一 ,采取针对性强的有效措施 ,确保突出矿井的安全生产     

俄气南供与天然气利用规划

介绍了俄气南供的供气方案，讨论了天然气的市场调查和价格的确定等问题。     

氯碱生产中的腐蚀与防护

介绍了氯碱装置中介质的腐蚀特性、常用材料的耐腐蚀特性及应用实例。     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465     

智能化原油及可燃气体泄漏监控系统

原有的可燃气体检测报警仪在技术上无法准确监控现场可能发生的原油或可燃气体的泄漏。为了保证油库的安全生产和科学管理，开发并应用适合油库的原油及可燃气体泄漏监控系统，具有重要意义。文章介绍了如何根据实际需要，应用工业控制计算机和仪表技术，开发智能化原油(可燃液体)及可燃气体泄漏监控系统。该监控系统已推广应用于大型油库及其它石化生产企业。实际应用证明，系统对各种可燃气体及液体泄漏均有很好的监控作用。     

塔巴庙区块气层录井参数分析研究

塔巴庙区块气藏属于低压、低渗气藏,储集层物性差异大、含气级别高,但含气非均质性强,录井解释评价困难。针对这一问题,开展了综合判断储集层物性和含气性方面的研究,分别探讨了钻时与全烃、钻井液性能与全烃、钻井液粘度与全烃、气测显示与测井参数和烃组分与气显示之间的关系,分析了其相关性及其在塔巴庙区块气层解释评价中的意义及作用。通过相关性研究,不但摸索出定性解释评价气层的方法,同时为今后深入研究录井相关参数关系,探索其内在规律,为实现准确解释评价储集层奠定了基础。