The prediction of transport parameters in filamentous fermentation broths based on results obtained in pseudoplastic polymer solutions

Transport phenomena studies on single phase “model” fluids are of limited value in biochemical engineering if they cannot be translated to the heterogeneous systems encountered in real fermentation processes. In this paper we discuss the utility of polymer solutions as models of filamentous fermentation broths for evaluation of: pipeline friction factors and impeller power numbers (turbine and helical ribbon). To a first approximation, polymer solutions can serve as suitable models for the prediction of laminar flow pressure drop in pipelines and turbulent power consumption in stirred tanks. However, results obtained on polymer solutions do not directly apply to filamentous fermentation broths for predictions of laminar flow impeller power consumption and the transition point for turbulent flow in stirred tanks. These discrepancies are believed to result from the existence of a time dependent yield stress in filamentous fermentation broths.     

磁放大器控制硅弧焊整流器性能的研究

本文针对硅弧焊整流器的控制性能,在分析铁磁材料特性的基础上,分别对单铁芯磁放大器和双铁芯磁放大器的结构和工作原理进行了深入的研究,提出了单铁芯磁放大器所存在的缺点以及双铁芯磁放大器的优点,使得硅弧焊整流器的设计采用双铁芯磁放大器,能够避免焊接时焊接电流波形的畸变,对提高焊接质量是有利的。     

压电双晶片型旋转精密驱动器动态特性和控制

提出了以自由端带有集中质量的悬臂式压电双晶片为驱动单元的新型冲击式旋转精密驱动器.制作了驱动器样机,建立了基于Lugre摩擦模型的驱动器动力学模型.对驱动器动态特性进行了仿真分析和实验对比研究.根据驱动器的动态特性,提出了冲击式压电双晶片型精密驱动器特定的定频调压控制方法.仿真分析结果和实验结果吻合较好,表明该动力学模型符合驱动器的动态特性,可用于对冲击式压电双晶片型旋转精密驱动器的理论分析.     

电解铝厂整流变电所直流大母线施工技术

介绍电解铝工艺设备中直流汇流母线的加工和安装施工技术.     

Interfacial Microstructure and Mechanical Properties of Al/Mg Butt Joints Made by MIG Welding Process with Zn-Cd Alloy as Interlayer

Butt joints between Mg alloy AZ31 B and pure Al 1 060 sheets were produced via metal inert gas welding process with Zn-Cd alloy foil. Crack-free Al/Mg butt joints between AZ31 B Mg alloy and pure Al 1060 sheets were obtained. Intermetallic compound layer 1 and layer 2 had formed in fusion zone/Mg alloy and the average thickness of the layer 1 was about 50 μm. The intermetallic compound layer 1 consisted of Al12Mg17 and Mg2Si phases while layer 2 consisted of Al12Mg17, Mg2Si and Mg Zn2 phases. The crack started from the IMC layer at the bottom of the joint and propagated along the brittle IMC layer, then expanded into weld metal during the SEM in situ tensile test. The highest tensile strength of the dissimilar metal butt joints could reach 46.8 MPa and the effect ofinterfacial IMC layer on mechanical property of the joint was discussed in detail in the present study.     

Ti和V对Fe中氢与位错交互作用的影响

研究了Fe-0.5wt-%Ti和Fe-0.5wt-%V合金中由氢与位错交互作用所形成的氢致冷加工内耗峰(H-CWP)。实验结果表明:合金元素对H-CWP、对氢与位错之间的交互作用有显著的影响,与氢作用愈强的元素,对H-CWP的影响愈大,内耗实验结果与力学性能之间存在着一定的联系.     

岸吊焊缝裂纹分析与改进措施研究

从材料的焊接性能、焊接结构、焊条、预热与焊后热处理、焊接工艺参数等角度对岸吊胎架焊缝裂纹进行了分析,提出了改进措施,取得了良好的效果。     

CO2气体保护焊机操作注意事项

介绍了焊工在CO2气体保护焊机的安装、使用、维护保养及维修中的注意事项。     

Ni-Cr-Fe-Si-B合金涂层及铝青铜基体熔合区组织的研究

采用钨极氩弧焊方法在铝青铜基体上施焊了Ni—Cr-Fe-Si—B合金涂层，并运用金相显微镜、扫描电子显微镜及能谱分析了喷涂层、熔合区及热影响区的组织形貌和成分分布。结果表明，喷焊时，在涂层与基体界面两侧各组元均发生了明显的扩散，Cu、Ni组元间可相互取代，基体融合区组织的基本组成仍为α (α γ2)，但同时也形成了Cu2FeAl7、NiAl3等新相，且融合区组织细小，涂层与基体间为冶金态结合。