双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

高温氨化合成GaN微晶

分别利用Ga2O3粉末和Ga2O3凝胶作为Ga源,采用NH3为N源,在950℃下,分别将两种反应物与流动的NH3反应20 min合成了GaN微晶。用X射线衍射(XRD)、扫描电子显微镜(SEM)、选择区电子衍射(SAED)对微晶进行结构、形貌的分析,特别是对两种不同途径合成GaN微晶的XRD进行了分析比较。结果表明,当Ga源温度为950℃时两种不同的合成途径均可得到六方纤锌矿结构的GaN单晶颗粒,在氮化温度为850℃和900℃时,利用Ga2O3粉末作为Ga源,仅有少量的Ga2O3转变为GaN;而采用Ga2O3凝胶作为Ga源,在相同的温度下,大部分凝胶经过高温氨化反应均可转化为GaN。     

从"天人合一"到"物我合一"——设计艺术中我国观念的转化

通过我国设计艺术中人与自然以及人与物古今观念的对比，试图分析这种观念的转化产生的深层社会背景和对设计的影响。     

套保稠油油田火烧油层可行性分析

从火烧油层的筛选标准、实际地质条件及室内物理模拟实验入手，对该油田火烧可行性进行了分析。分析结果认为，套保油田进行火烧总体上是可行的，在实际火烧时应避开底水的影响，火烧区域应选在构造高部位或仅烧其主力层。     

伶仃洋三维潮流输沙的数值模拟

作者使用垂向坐标变换技术，结合有限差分方法建立了三维潮流输沙的数学模型。为了增加模型的稳定性和减少数值耗散，对悬沙对流扩散方程中的水平对流项采用三阶迎风格式离散。应用本模型对伶仃洋的枯季和洪季的潮流输沙的悬沙场进行了数值模拟，将模拟结果与实测资料进行比较，二者吻合较好。模拟结果分析表明：伶仃洋悬沙运动主要集中在西滩，对伶仃航道影响不大；洪季水体含沙浓度高于枯季；水体含沙浓度沿水深存在浓度梯度，且洪季的浓度梯度明显大于枯季。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

大型连杆流线简易试验方法

介绍了一种大型连杆流线的简易试验方法及其评价原则。该方法可清晰显示流线，并适合任何尺寸和形状的锻造连杆的流线试验。     

微带型Wilkinson功分器设计与实现

小型低功耗器件是射频电路设计的研究热点,而微带技术具有小型化低功耗的优点,为此在介绍微带型Wilkin-son功分器工作原理的基础上,使用基于矩量法的ADS软件设计、仿真和优化计算相关数据参数,并制作了一个微带功分器实例,最后对加工的样品进行实测,获得与仿真值吻合较好的预期结果。     

Estimation and Optimization of the Principal H-Maser Parameters

The scale along the coordinate axes in the equations of motion hitherto used for an H-maser (in relative units) is shown to depend on Q as the quality factor for an H-maser. This hinders both analysis of the operation of the H-maser and optimization of its parameters. The modified equations of motion proposed here do not have that shortcoming. We determine the atomic flux into the bulb that gives the H-maser the best metrological characteristics.     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.