层状介质中重力,地震联合反演的迭代算法

本文提出一种用于层状介质中重力、地震资料联合反演层速度、层密度及弯曲界面深度的迭代算法。该方法通过引入加权最小平方目标泛函,将层状介质中的重力、地震资料联合反演问题转化成具体的优化问题。为了得到反问题的最优解,文中系统地研究了层状介质中双摄动处理技术,以及层状介质中波场摄动的一阶 Born 近似解与理论重力异常摄动解。并应用 Tarantola 的反演理论,导出了梯度算子的计算公式。然后应用最速下降法给出了求取最优解的具体算法,得到了一种类似于地震偏移与空间更投影的迭代反演方法。对理论模型进行重力、地震联合反演的结果表明,该方法不仅可碱少未知参数的个数,提高反演的收敛速度,而且可减少反演的不适定性,不失为一种可行的多参数反演方法。     

太钢3#高炉重力除尘器大件吊装

太钢3#高炉大修改造是集团公司重点外部工程项目之一，工程量大，工期紧，施工场地狭小，而质量要求较高。如何采取科学、经济的设备吊装方案，对整个项目经济指标的实现，意义重大。文章详细介绍了太钢3#高炉重力除尘器大件整体吊装方案。通过实际采用，取得良好的经济效果。     

INTERACTION OF VORTICES WITH A PROGRESSIVE SURFACE WAVE

ＩＮＴＥＲＡＣＴＩＯＮＯＦＶＯＲＴＩＣＥＳＷＩＴＨＡＰＲＯＧＲＥＳＳＩＶＥＳＵＲＦＡＣＥＷＡＶＥＷａｎｇＬｉｎ－ｌｉｎ；ＭａＨｕｔ－ｙａｎｇ（ＧｒａｄｕａｔｅＳｃｕｄｏｆＡｃａｄｅｍｉｃａＳｉｎｉｃａＢｅｉｊｉｎｇ１０００３９Ｐ．Ｒ．Ｃｈｉｎａ）Ａｂ...     

基于MODWT和BP神经网络的微电网故障诊断方法

近年来,随着微电网技术的持续发展,电力用户对其供电可靠性的要求也不断提高,因此微电网故障诊断研究也变得越来越重要。提出了一种基于极大重叠离散小波变换(MODWT)和反向传播(BP)神经网络的微电网故障诊断新方法,并通过仿真与算例进行了验证。结果表明:该方法能快速、准确地识别出故障类型,且不受故障初始相位角和过渡电阻等因素的影响;与现有的基于离散小波变换和反向传播神经网络的诊断方法相比所提出的方法可以提供更好的故障分类精度。     

Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.     

Horizontal wells and steam-assisted gravity drainage

Petroleum can be produced more efficiently using horizontal wells instead of conventional wells. For a typical 16 hectare well spacing, the pressure drawdown is as small as one-fiftieth of that for conventional wells. In some cases, where coning is a problem in conventional production, horizontal wells allow operation with much less coproduction of the displacing fluid. In the thermal recovery of bitumen and heavy oils, the Steam-Assisted Gravity Drainage process with horizontal production wells allows the systematic sweeping of the reservoir with economic production rates and without steam bypass. This paper described and reviews the application of horizontal wells to the production of heavy crude oils and bitumen by both non-thermal and thermal methods.     

自重施加方式对高拱坝廊道结构应力及配筋的影响

自重工况一般是高拱坝内廊道配筋设计的控制工况,由于高拱坝施工过程的特殊性及复杂性,有限元计算中自重有多种施加方式。结合工程实例,对高拱坝基础廊道结构进行三维有限元分析,比较不同自重施加方式对廊道结构应力及配筋的影响。研究结果表明:按整体自重考虑时,廊道结构应力及配筋面积明显偏小;全部按分缝自重考虑时,廊道结构应力及配筋面积明显大于按施工过程考虑自重的结果;为符合实际施工过程及结构承载规律,保证结构安全及经济合理,在拱坝结构的有限元计算中应按照施工过程考虑自重荷载。该研究成果对泄洪孔结构的应力分析也具有参考价值。     

Fuzzy PID control of space manipulator for both ground alignment and space applications

Considering gravity change from ground alignment to space applications, a fuzzy proportional-integral-differential (PID) control strategy is proposed to make the space manipulator track the desired trajectories in different gravity environments. The fuzzy PID controller is developed by combining the fuzzy approach with the PID control method, and the parameters of the PID controller can be adjusted on line based on the ability of the fuzzy controller. Simulations using the dynamic model of the space manipulator have shown the effectiveness of the algorithm in the trajectory tracking problem. Compared with the results of conventional PID control, the control performance of the fuzzy PID is more effective for manipulator trajectory control.     

基于重力坝三维设计的CAD动态交互系统开发

为了在可研阶段合理、快速地制定重力坝设计方案,减少设计周期和成本,采用极限状态设计的方法,利用VB 6.0可视化编程工具开发出了一套能够与CAD动态交互的重力坝三维设计系统。该系统通过对Auto-CAD的二次开发实现了重力坝的三维参数化建模,并对所建三维模型进行结构计算,将设计与计算紧密结合,通过动态交互简化了大量复杂数据的计算,达到精确、快速完成断面设计的目的。经实践检验证明,该系统大大提高了断面设计效率,实用性强,对可研阶段的方案比选具有重大意义。     

基于类内差异和类间重叠的有效性函数

模糊C-均值(FCM)聚类算法的一个主要问题是需要事先确定聚类的数目,为此定义了类内差异度和类间重叠度来分别度量同一个聚类中数据的相似度和不同聚类间的分离程度,进而基于这两个度量提出一个新的有效性函数用于判定最佳聚类数目。实验结果表明,该有效性函数能有效地判定聚类数目,并且有较好的鲁棒性。