管内装元件强化传热的技术经济评价

提出了一种管内装元件强化传热的技术经济评价方法，此方法综合考虑了强化换热器管内传热膜系数的提高和管内流体阻力的增大，与普通的管壳式换热器相比，所带来的投资费用和使用费用变化，这个变化量可用净现值增量△NPV来表示。根据△NPV值来评价强化传热技术，从而为强化传热技术的开发和推广及进行决策提供指导。     

Upper bounds for solar thermophotovoltaic efficiency

The main components of thermophotovoltaic (TPV) devices are the primary lens (or mirror), the absorber, the PV cell, and a photon recuperator system. A theory integrating all these components is used in this paper to analyse a particular type of TPV device (plane disk absorber and PV cell). The TPV efficiency is maximized by using three optimization parameters, namely absorber, PV cell temperatures, and cell voltage. Almost ideal operation conditions are envisaged and upper bounds are obtained for the TPV efficiency. They are strongly dependent on PV cell bandgap and radiation concentration. Preliminary results suggest the existence of an optimum solar radiation concentration ratio. The improvement in thermal design quality allows the usage of PV cells based on wide bandgap semiconductors.     

60Si2Mn合金钢发蓝泛红的分析研究

本文探讨了60Si2Mn合金钢发蓝原理，针对其膜层泛红问题，分析了热处理、表面前处理、发蓝及浸油等过程对发蓝质量的影响，由此采取了相应的技术措施，生产实践证明发蓝质量稳定，生产效率明显提高。     

裂齿矩形翅片板翅式换热器优化设计的分析

对裂齿矩形翅片板翅式换热器中的裂齿矩形翅片的传热效率作了分析,并以单位质量材耗的换热能力最大为目标函数,分析研究了在不同雷诺数(Re)的操作条件下裂齿矩形翅片间角度、翅片厚、长度、宽度及极厚之间的关系。结果表明:在气体换热的场合下,当Re在某一范围时翅片可有效地起到强化传热的作用。当板厚为5mm,翅片厚为3mm,翅片间夹角为45°～70°,Re为2×10~3～8×10~3,最佳翅片纵向间距与翅片长度和翅片厚度乘积的平方根的比为1.5～2.5,最佳翅片尺寸系数为3～5时,传热强化效果较好。     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

Effect of Heat Treatment on Luminescent Properties of White Organic Light Emitting Device

The white organic light emitting device (OLED) with single-structure using a polymer blend as the light emitting layer is fabricated. Heat treatment is used to control the ratio between the intensities of main electroluminescent spectral peaks. The electroluminescent spectrum of our device is quite similar to that of white inorganic LED produced by Nichia Corporation after being annealed, and its turn-on voltage can be decreased by 1V.     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

The Difference in Turbulent Diffusion between the Active and Passive Scalars in a Thermally Stably Stratified Medium

The difference in the turbulent diffusion between the active (heat) and passive (mass) scalars in a thermally stably stratified medium is investigated. The axisymmetric problem is treated on the formation of a turbulent circulation flow above a heated disk and on the turbulent diffusion of a passive scalar (impurity) from a continuous surface source in a stably stratified medium. The results indicate that the thermal stratification causes appreciable differences in the coefficients of turbulent transfer between the active (heat) and passive (mass) scalars. This means that the assumption of the identity of the coefficient of turbulent diffusion of heat and mass, employed in conventional models of turbulence, produces significant errors in estimating the heat and mass transfer in a thermally stably stratified medium.     

Improved Matrix-Filler Adhesion

Enhanced matrix-filler adhesion is realized after filler treatment with a surface treatment process. The hydrosol/coupling agent treatment was applied to a wide range of inorganic and organic fillers, and adhesion to a variety of matrix resins was improved. Scanning Electron Microscopy (SEM) was used to determine the locus of failure in the filled systems. The locus of failure shows the relative degree of adhesion between the filler and the polymer matrix. Significant improvement in adhesion in humid environments is also observed.     

Mixed anaclitic-introjective psychopathology in treatment-resistant inpatients undergoing psychoanalytic psychotherapy.

Utilizing data from the Riggs-Yale Project, 45 male and 45 female 18-29-year-old treatment-resistant inpatients undergoing intensive psychoanalytically oriented treatment were studied. Twenty-seven mixed-type anaclitic-introjective inpatients were compared with 29 "pure" anaclitic and 34 "pure" introjective inpatients. At intake, mixed-type inpatients were more clinically impaired (i.e., were more symptomatic, cognitively impaired, and thought disordered) and more vulnerable (i.e., less accurate object representations and more frequently used maladaptive defense mechanisms) in comparison with clearly defined anaclitic and introjective patients. Mixed-type patients, however, improved significantly more in the course of psychoanalytically oriented treatment, in terms of clinical functioning (i.e., symptoms, cognitive functioning) and psychological vulnerability (i.e., utilization of more adaptive defense mechanisms). (PsycINFO Database Record (c) 2010 APA, all rights reserved)