α-Fe_2O_3(SO_4~(2-),Sn)气敏电阻的温度响应特性

在气敏温度区域内研究了α-Fe_2O_3(SO_4~(2-),Sn)材料的电阻-温度特性,认为表面结构的变化导致温度特性出现峰值并呈现气敏性。可利用空气中电阻温度特性提供的信息改性或发现新的气敏材料。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Study on ASTM E399 and ASTM E1921 standards

Costs of ASTM E399 and ASTM E1921 tests, which were developed to determine the fracture toughness (K_Ic) and the ductile–brittle transition temperature of ferritic steels, respectively, are considered high and the procedures are also very complicated. In this study, a method, which is more cost‐effective and easier to carry out, is proposed.     

Sicherer und wirtschaftlicher Betrieb von Kraftwerken – Ergebnis der Forschung im Bereich Werkstoffe,Auslegung und Instandhaltung

Safe and Economic Operation of Power Plants – Research Results in the Field of Materials, Design and Maintenance Components of power plants which undergo high temperatures are subjected to complex loading situations. The requirements on the used materials result from the special operation conditions of the plants and have to be adjusted to the steadily growing requirements on higher efficiency of the complete power plant as well as to those of safe and economic operation. The expenses for control and downtimes are directly connected with economic efficiency and availability. However, in case of new procedures or components it is not possible to revert to the existing know‐how. Different failure mechanisms than known before can occur. The same goes for the load situation. Therefore the knowledge base has to be extended to in‐advance or even parallely running scientific examinations that life assessment and maintenance strategies can be applied which guarantee the operational reliability and the efficiency of the plant. The main emphasis of these F&E works has to be put on condition monitoring based on actual operational data, the standard materials’ and component’s behaviour (deformation, damage and failure behaviour) in connection with design of components and the related material laws. In the framework of applied AVIF projects, following problems are handled:. – qualification of materials by determinating parameters related to practise. – optimal design of components by making available material laws and numerical tools. – economic manufacturing of components by qualifying processing methods such as welding. – The results can be transferred to concepts for safe and economic operation of power plants, especially for newly introduced materials for which there is no operational experience available.     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

马鞍山煤矿瓦斯地质理论在防突工作中的应用

总结了实际工作中防突管理的经验和问题 ,探讨了科学理论与具体实际的有机结合与统一 ,采取针对性强的有效措施 ,确保突出矿井的安全生产     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.