有机介质中合成二硫化钛

本文研究了硫化氢与四氯化钛在某些有机介质中的反应，并提出了一个合成二硫化钛的新方法。该法是将干燥的硫化氢通入沸腾的四氯化铁的α－氯代萘溶液中，使硫化氢和四氯化钛发生复分解反应而生成二硫化钛。方法简便易行。Ｘ－射线物相鉴定及化学分析结果表明，产物为单一物相的、符合化学计量的二硫化钛。     

制氢尾气二氧化碳回收装置设计

对制氢尾气二氧化碳的回收装置进行了简捷设计，流程分析，并对换热装置的换热量和传热面积给出了算法和有关数据。     

熔敷金属扩散氢逸出特性研究

采用酒精法测量扩散氢 ,研究了焊条熔敷金属扩散氢含量以及在测氢过程中扩散氢逸出量与逸出时间的关系 (逸出特性 )。研究结果表明 ,熔敷金属扩散氢逸出特性受扩散氢含量、焊道数、熔敷金属化学成分和表面状态等多种因素的影响。熔敷金属扩散氢 (HDo)可以分为快速逸出扩散氢 (HDq)和慢速逸出扩散氢(HDs)两部分     

AP的安全制备（英）

1 IntroductionThe ammonium perchlorate ( AP)-based compositepropellant is currently the most widely used one becausethis propellant has good burning characteristics and me-chanical properties. One of the few serious drawbacks ofthe AP-based propellant is that its products of combus-tion, which include HCl, chlorine, and chlorine oxides,cause atmospheric pollution. Increasing concern for aclean atmosphere in recent years has resulted in a com-pelling need for developing a chlorine-free,enviro…     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

Specimen preparation and image processing and analysis techniques for automated quantification of concrete microcracks and voids

Specimen preparation and image processing/analysis techniques were developed for use in automated quantitative microstructural investigation of concrete, focusing on concrete microcracks and voids. Different specimen preparation techniques were developed for use in fluorescent and scanning electron microscopy (SEM) of concrete; then techniques produce a sharp contrast between microcracks/voids and the body of concrete. The image processing/analysis techniques developed specifically for use with concrete address the following usages: automatic threshold; development of intersecting microcracks/voids and connected voids; distinction of microcracks form voids based on geometric attributes; and noise filtration.     

纳米陶瓷的制备

纳米陶瓷材料可显著降低材料的烧结致密化程度,节约能源;并可改善陶瓷材料的性能,提高其使用可靠性。主要介绍了纳米陶瓷的制备方法,包括纳米陶瓷粉体的制备、成型和烧结。     

纳秒级上升时间的高压脉冲群电源

按照IEC 61000-4-4/GB 17626.4—1998的要求，首先应用PSPICE仿真确定电路中各元件的参数值，然后基于拉普拉斯变换用MATLAB求解二阶电路验证各元件参数。在此基础上研制了一台以开关电源作为高压直流电源、以氢闸流管作为主控开关的脉冲群电源。该电源体积小、重量轻、效率高、成本低廉。试验结果表明，其输出信号符合标准要求，可用于快速瞬变脉冲群抗扰度试验。     

Study of miscibility enhancement in poly(styrene‐co‐4‐vinylphenol)/poly(ethylene oxide) blends by the spin labelling method

The electron spin resonance (ESR) spectra of end‐group spin labelled poly(ethylene oxide) (SLPEO) using 2,2,6,6‐tetramethyl‐piperdine‐1‐oxyl nitroxide and its blends with poly(styrene‐co‐4‐vinylphenol) (STVPhs) of different hydroxyl contents were recorded over a wide temperature range. For a blend of SLPEO and pure polystyrene (PS), the ESR spectrum was composed of a single motion component, indicating that PS was immiscible with PEO. For blends composed of SLPEO and different‐hydroxyl‐content STVPhs, two spectral components with different motion rates were observed over a certain temperature range. The difference between the motion rates should be attributed to micro‐heterogeneity in the blends, with the faster rate corresponding to a nitroxide radical motion trapped in the PEO‐rich domain and the slower rate corresponding to a nitroxide radical motion trapped in the STVPh‐rich domain. Variations in the values of a number of the ESR parameters (T_a, T_d and T_50G) and the apparent activation energy (E_a) with hydroxyl content in the blends indicated that the miscibility of the blends increased with increasing hydrogen‐bonding density due to specific interactions between the hydroxyl groups in STVPh and the ether oxygens in PEO. Copyright © 2004 Society of Chemical Industry     

Estimation of errors of hydrogen standard time scale preservation taking account of systematic frequency changes

Metrological characteristics of active hydrogen frequency standards are investigated on the basis of internal and external comparisons. The stability of random changes and drift of hydrogen frequency standards and also the potential capabilities of time scale preservation with effective consideration of systematic changes in their frequency are demonstrated. __________ Translated from Izmeritel’naya Tekhnika, No. 3. pp. 42–45, March, 2007.