氢电弧等离子体法制备的纳米镍铈粒子的催化特性

利用氢电弧等离子法制备具有储氢特性纳米镍铈粒子，并在气相苯加氢反应中研究了其催化特性，发现其催化活性与储氢特性及表面层中ＮｉＣｅ合金存在有关，且具有高的选择性和热稳定性，这与纳米粒子独特的结构及铈的加入有关。     

工艺因素对金属封装外引线弯曲疲劳的影响

考察了金属封装外壳制造工艺对外引线弯曲疲劳的影响,发现电镀镍是导致外引线弯曲次数明显减少的最主要工艺步骤,且随镀镍层厚度的增加,弯曲次数减少。此外还讨论了外引线的氢含量和晶粒度对引线抗疲劳能力的影响。     

化肥厂合成气及重整氢真空变压吸附制取高纯度氢气

从设计、生产操作和经济效益3个方面阐述了以化肥厂合成气及重氢为原料，通过真空变压吸附（VPSA）装置制取高纯度氢的过程。工业应用结果表明，该制氢工艺是一项操作简便灵活，制氢费用较低的工艺路线。VPSA装置技术和设计上的特点能够保证大的操作弹性、高的产品氢纯度和较高的氢气回收率。在36％－51％的低限负荷下，通过适当调整吸附时间，可获得纯度99％的氢气产品，89％－92％的氢气回收率。     

Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

碱式苦味酸铅针刺药的应用研究

提出了以碱式苦味酸铅为主体的针刺药在组合点火管中的应用，并对其针刺药的点火性能及能量传递进行了讨论，阐明了此类针刺药良好性能和应用价值。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

二维谐振子与二维氢原子的能量及波函数

借助于ＳＵ(１,１)代数,找出了二维谐振子与二维氢原子的能量及波函数间的关系．     

2.0 Mt/a渣油加氢脱硫装置新氢压缩机性能标定

介绍了中国石化茂名分公司 2 .0Mt/a渣油加氢脱硫装置中的 4M80 30 /2 2 2 0 0 BX型新氢压缩机的特点、技术特征及标定情况。采用国际通用标准对压缩机气体组成、容积流量、轴功率、进排气压力和进排气温度等指标进行了测定。标定表明 ,该机组设计方案合理 ,运转平稳 ,性能指标达到设计要求 ,较好的满足了工艺操作的需要     

Effect of Pressure Gradient on Heat Transfer of Impinging Submerged Circular Jets

An experimental and numerical study have been carried out to investigate the distribution of radial local heat transfer coefficients of impinging submerged circular jets. Good agreement is achieved between the experimental results and the predicted value. Results show that the outer peak usually occurs at the radial location of r/d= 1.8~2.0, in which transition from laminar to turbulence happens resulting from disappeared pressure gradient abruptly, and that the inner peak appears rigidly at r/d=0.5, where the boundary layer has a minimum thickness because of elevating pressure gradient.