浅论太阳电池在通信工程中的应用

介绍了太阳电池应用的一般要求和太阳能供电系统的组成及运行，给出了工程设计个常用的太阳电池容量计算方法，并提出太阳能供电系统运行维护注意事项。     

鹰嘴岩隧道软弱破碎岩体的开挖与施工

渫水皂市水利枢纽左岸上坝公路鹰嘴岩隧道围岩主要为Ⅱ、Ⅲ、Ⅳ、Ⅴ类围岩，地质条件复杂，成洞条件差。在隧道施工中，遵循“短进尺，弱爆破、少扰动、早支护”的原则，及时进行监控量测，采取有效的加固措施，取得了良好效果，确保了工程进度与安全。     

压缩奇偶相干态的熵压缩特性

用数值方法讨论了相干态强度、相位角和压缩参数对压缩奇偶相干态位置熵和动量熵压缩特性的影响。结果表明，压缩奇偶相干态的位置熵和动量熵均可呈现压缩性，压缩偶相干态的最大熵压缩度比压缩奇相干态的要大。熵压缩度与相干态强度、相位角和压缩参数均有关系，但压缩因子对场熵压缩的影响最大。当其它条件一定时，压缩偶相干态在压缩参数|β|=O．95时，位置熵(或动量熵)的压缩度最大，但压缩奇相干态无此特点。     

略论贵州省化工企业职业教育的发展

从目前市场需求和就业率出发，进行形势分析，提出优化专业设置、加强实践环节、提高高职学院办学层次、推进“双证书”制度等改革方法，以促进化工职业教育的发展。     

SHG对污水的处理效果

SHG对不同污水的COD的降低,DO的增加,及色、臭味和浊度的降低效果明显。     

Simulation of runoff and phosphorus transport in a Carpathian catchment,Slovakia

A comprehensive, GIS‐based modelling approach is developed to estimate runoff and phosphorus transport within a watershed at a daily time step. The approach relies on the use of GIS data for deriving major critical model parameters that exhibit distinct spatial variability over the catchment. Surface runoff is calculated by a modified rational method, which depends upon rainfall intensity, soil moisture status, slope, land‐use and soil characteristics. Phosphorus loading is estimated as a function of the runoff volume and the event mean concentration for different land use categories. A diffusive approximation method is used to trace runoff and phosphorus transport to the basin outlet. The modelling approach is tested in the Margecany catchment, Hornad River basin, Slovakia, to simulate runoff, phosphorus loading, and its transport on a daily time scale using data observed between 1995 and 2000. Satisfactory results of the hydrographs and phosphorus concentration at the basin outlet are obtained, though more efforts regarding the phosphorus cycling and its biochemical reactions need to be clarified by further research. Copyright © 2006 John Wiley & Sons, Ltd.     

舞钢管线钢的开发与生产

系统介绍了舞钢开发的针状铁素体型X70宽厚板的设计思路、工艺特点和实物水平；采用电炉 炉外精炼 连铸 TMCP工艺生产的X70宽厚板满足西气东输专用技术条件的要求，并批量应用在西气东输主干线工程中。     

Simulation of the Forming Behaviour of a Boron Modified P91 Ferritic Steel

The forming behaviour at high temperature of a modified 9%Cr‐1%Mo (P91) ferritic steel containing B and Ti for elevated temperature service was investigated. The microstructure of the as‐received material is mainly martensite at room temperature, but special etching revealed prior austenite grains of about 25 μm in size. Torsion tests were conducted at temperatures in the range 850 to 1250 °C to simulate the hot rolling process under comparable conditions of temperature, strain rate and strain. The deformation data obtained from these tests were correlated with the Garofalo equation with a stress exponent of 4.6 and an activation energy of 315 kJ/mol. This equation was used to predict the formability behaviour for the rolling process and also to determine the maximum forming efficiency and stability of the steel. A temperature of 1200 °C is recommended to conduct the forming process.     

Reliability evaluation and optimisation of imperfect inspections for a component with multi-defects

In this paper, a model is developed to evaluate the reliability and optimise the inspection schedule for a multi-defect component. The model uses a non-homogeneous Poisson process (NHPP) method in conjunction with a delay time approach. The inspections are designed to detect any defects in the component, however it can be imperfect. The defect is a definable state before a functional failure happens to the component. Occurrences of defects are assumed to follow an NHPP and a defect will be minimally repaired if it is identified during an inspection. It is shown that the failures occurring in an interval of inspection will also follow an NHPP. The situation of imperfect inspections and non-constant inspection intervals are considered. An algorithm is presented to optimise the intervals of inspections in order to maximise the reliability of the component, and the properties of the algorithm are shown. A numerical example with parametric study is given to show the performance of the model and the algorithm.     

Biofiltration of toluene in the absence and the presence of ethyl acetate under continuous and intermittent loading

BACKGROUND: Two peat biofilters were used for the removal of toluene from air for one year. One biofilter was fed with pure toluene and the other received 1:1 (by weight) ethyl acetate:toluene mixture. RESULTS: The biofilters were operated under continuous loading: the toluene inlet load (IL) at which 80% removal occurred was 116 g m^?3 h^?1 at 57 s gas residence time. Maximum elimination capacity of 360 g m^?3 h^?1 was obtained at an IL of 745 g m^?3 h^?1. The elimination of toluene was inhibited by the presence of ethyl acetate. Intermittent loading, with pollutants supplied for 16 h/day, 5 days/week, did not significantly affect the removal efficiency (RE). Biomass was fully activated in 2 h after night closures, but 6 h were required to recover RE after weekend closures. Live cell density remained relatively constant over the operational period, while the dead cell fraction increased. Finally, a 15 day starvation period was applied and operation then re‐started. Performance was restored with similar re‐acclimatization period to that after weekend closures, and a reduction in dead cell fraction was observed. CONCLUSION: This study demonstrates the capacity of the system to handle intermittent loading conditions that are common in industrial practices, including long‐term starvation. Copyright © 2008 Society of Chemical Industry