一种白光测速仪在热锯区域中的应用

阐述白光测速仪的工作原理及优缺点,介绍其在莱钢大H型钢生产线热锯区域的应用.     

Effects of silicone oil and polymeric modifiers on the mechanical properties of highly filled LLDPE

The effects of coupling agents, silicone oil, and three types of polymeric modifiers on the mechanical properties of linear low density polyethylene (LLDPE) composites highly filled with aluminium hydroxide [Al(OH)₃] were studied. Polymeric modifiers that contain polar groups, such as silane‐grafted polyethylene (Si‐g‐PE) and acrylic‐acid‐grafted ethylene‐vinyl acetate copolymer (AA‐g‐EVA), improve the mechanical properties dramatically, while nonpolar modifiers improve them to some extent. When Al(OH)₃ was treated using a titanate coupling agent, the silicone oil increased the impact strength and elongation at break of the LLDPE/Al(OH)₃ composites. Introduction of a polymeric modifier containing polar groups destroys the beneficial effects of silicone oil on film mechanical properties, while the introduction of a nonpolar elastomeric polymeric modifier retains the high impact strength and elongation at break. SEM analyses provide the indirect evidence of the encapsulation of silicone oil around the filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 121–128, 2002     

Design of the low power wake-up receiver for internet of things communication

A wake-up receiver with high energy efficiency and low power consumption is proposed for solving the power consuming problems of wireless nodes communication in the Internet of Things. The proposed wake-up receiver based on the wake-up mechanism can effectively schedule the network nodes communication, and use the simple envelope detection structure to achieve frequency down-conversion, which can flexibly manage energy and reduce power consumption. Based on UMC 65nm CMOS process technology, the wake-up receiver is designed and simulated. The results show that it can achieve S₁₁ of -21dBm and a sensitivity of -75dBm at a data rate of 1Mb/s, when operating at the central frequency of 780MHz and input signal adopting an on-off keying (OOK) modulation, and the power consumption is 82μW at 1.2V voltage supply.     

Influence of depth-thickness ratio of mining on the stability of a bedding slope with its sliding surface in concave deformation

In order to study the influence of depth-thickness ratio on bedding slope stability, whose sliding surface is flexural concave in shape under mining conditions, this paper aims to study the characteristics of deformation and damage of bedding sliding with depth-thickness ratios of 200:1, 150:1, 120:1, 100:1 and 50:1by adopting numerical simulation analysis software combined with laboratory-made ‘‘under the influence of mining variable sliding surface slope similar simulation test bed", and to propose identification methods for slope stability under the influence of mining. The results show that mining activities under the slope reduce slope stability. With a decrease in the mining depth ratio, the influence of mining on the slope increases gradually, and the damage to the slope gradually expands, the stability of the slope gradually reduces, fracture occurs on the slope toe and the central fissure gradually develops to the surface,and reaches slide threshold when the depth-thickness ratio is 50:1.     

论焊接结构生产的技术改造

本文讨论了焊接结构生产技术改造的有关问题，包括总思路及总目标、自动化的基本框架、按低成本自动化的原则设计生产线和关键技术问题的论述。     

棒线材连轧中的微张力闭环控制

介绍了棒线材连轧中微张力闭环控制的基本思想及方法，并分析了微张控制技术的应用条件。     

低碳低合金铸钢力学性能的研究

利用Olympus光学显微镜、扫描电镜(SEM)及能谱分析(EDAX)探讨了等温淬火工艺对低碳低合金CrMnSi铸钢力学性能的影响,并通过XRD定量分析了相的组成.结果表明,合适的等温淬火工艺,可获得一定数量的贝氏体和残余奥氏体(约6%)的复合组织,冲击断口形貌由解理刻面变为韧窝状,铸造成形无缺口试样(10 mm×10 mm×55 mm)的冲击韧度由ακ≤30 J/cm2增加至ακ≥170 J/cm2,硬度HRC≥40,具有较高硬度和冲击韧度的配合.     

铝—钢双金属复合轧制层厚比及轧制力的研究

用实验方法研究了铝－钢双金属复合轧制时层厚比的变化规律。给出了双金属复合时轧制力的计算式。     

初探混联法生产氧化铝的工艺优化

在目前的生产条件下。通过大量的混联法物料衡算，定量地研究了供矿铝硅比、熟料铝硅比和拜年法赤泥铝硅比对混联法的制造成本、能耗和拜年法与烧结法的生产比例的影响规律，提出我国混联法生产进一步优化的方向和途径。并开发了研究和评价的计算软件。为混联法的生产和设计的进一步优化奠定基础。