Mixing Center of a Channel

For longitudinally uniform stretches of waterways there is a mixing center for the across-channel location of a steady point source in steady flow, such that complete mixing is achieved as soon as possible and there is no concentration overshoot at either of the two shorelines. A mathematical definition of the mixing center is the zero of the first oscillatory cross-channel diffusion mode. With the shorelines plus four interior data points across the channel, the starting estimate for the mixing center suffices to keep peak shoreline concentrations to within 6% of optimal. For comparison, a source at mid flow gives 18% shoreline concentration overshoot in the test case. Should very high precision be required, the Appendix gives an iterative construction that converges to the first oscillatory diffusion mode.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

雾化水流计算模式

本文描述了雾化水流现象并提出了雾化水流的一个计算模型。得出了雾化水流影响领域的各种不同的计算公式和方法。     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

新型双旋流平焰烧嘴的研制与应用

介绍了一种新型双族流平焰烧嘴的设计思路、结构参数及工业试验结果。其结构特点是每个部件都易装易卸，其煤气旋流器的位置可根据煤气压力变化进行调节，无需稳焰器就可保证煤气压力在较大范围波动时，都可形成稳定的平展火焰。     

管外上升R－113流体的沸腾换热试验

详细介绍了Ｒ－１１３流体管外上升流动的沸腾换热试验，包括试验台架、流量计和温度测量的修正，以及试验数据。拟合的换热关系式为ｑ＝５２８（Ｔｗ─Ｔｓ）１．３３。     

A BOUNDARY INTEGRAL EQUATION AND ITS NUMERICAL SOLUTION OF POTENTIAL FLOW AROUND SURFACE-IRREGULA-RITIES

In this paper,using complex functional theory,the authors turn the potentialflow around the surface irregularities in a pressure conduit and semi-infinite platforms intoDirichlet problem.Based on Schwarz formula and by the application of Plemelj's formula,theauthors change the problem into the integration of a Cauchy boundary integral equation in theflow plane through the substitution of variables.Using numerical integration,the authors obtainthe velocity distribution and pressure coefficient along surface irregularities and platforms.Thephysical concept of this method is clear,the convergent speed is rapid and the computative effi-ciency is high.The calculated values agree well with the measured results.It is an effective andsimple method in solving potential flow.     

NUMERICAL SIMULATION OF STRATIFIED FLOW WITH BOTH VERTICAL TEMPERATURE GRADIENT AND VERTICAL SALINITY GRADIENT

Density stratified flow with both the vertical temperature gradient and the verti-cal salinity gradient is simulated numerically, in which turbulent terms are calculated by a sim-plified turbulence stress/flux algebraic model. The feature of stratification and turbulence is de-scribed correctly by the model. The computational results agree well with the experimental data.However, the k-e turbulence model is not so successful.     

节流式差压流量计的发展和现状

文章介绍节流式差压流量计的特点及标准化进程，煤气流量测量中存在的难点以及正在试图解决的途径。     

Ultrasonic nondestructive evaluation of fibre-reinforced composite materials — a review

A framework is presented for examining the effectiveness of limiting and modelling arguments used in the analysis of fluid flows. It consists of examining the consequences of the arguments on the flow problem as a whole and breaking down the limiting/modelling process into a sequence of steps and associated sequence of flow problems, termed here as ‘lidels’. The notion of validity of lidels is given. Several examples are given to explain the present approach. Invited general lecture at 3rd ACFM, Tokyo, September 1986