Enhancement of resistance to galvanic corrosion of ZE41 Mg alloy by equal channel angular pressing

The galvanic corrosion behavior of as-received and ECAPed ZE41 Mg alloy coupled with Al7075 alloy is investigated using zero resistance ammeter in three different corrosive environments, 0, 0.1, and 1 M NaCl, to mimic the conditions experienced in engineering applications. The mechanism of galvanic corrosion for the ZE41 Mg–Al7075 aluminum alloy is explained. It is observed that a robust surface film containing a composite layer of oxide/hydroxide of magnesium and aluminum is established in deionized water (0 M). However, only a single layer of magnesium oxide/hydroxide is detected in chloride-containing environments. Equal channel angular pressing (ECAP) improved the resistance to galvanic corrosion by 58% and 54% when compared with the as-cast counterparts in 0 and 1 M NaCl solution, respectively. In contrast, galvanic corrosion resistance decreased by 26% in 0.1 M NaCl after ECAP while the as-received samples evinced pits unfavorable to be used in engineering applications. ECAP is a promising method to combat galvanic corrosion encountered by ZE41 magnesium alloy used in automobiles and components of military vehicles.     

Corrosion of Mg alloys EV31A,WE43B,and ZE41A in chloride- and sulfate-containing solutions saturated with magnesium hydroxide

This study studied corrosion in 0.1 M Na₂SO₄, 0.1 M NaCl, and 0.6 M NaCl, all saturated with Mg(OH)₂, using weight loss, hydrogen evolution, and electrochemical measurements. Corrosion was similar in all cases. Nevertheless, the corrosion rates were alloy-dependent, were somewhat lower in 0.1 M Na₂SO₄ than in 0.1 M NaCl, and increased with NaCl concentration. The corrosion damage morphology was similar for all solutions; the extent correlated with the corrosion rate. The corrosion rates evaluated by the electrochemical methods were lower than those evaluated from hydrogen evolution, consistent with the Mg corrosion mechanism involving the unipositive Mg⁺ ion.     

Corrosion of hot-dip-galvanised steel and zinc alloy-coated steel in ammonia and ammonium chloride

There are many potential causes of corrosion in animal buildings. Animals exhale large quantities of moisture into the air creating high relative humidity in the building if the moisture is not properly vented. High humidity increases the potential for condensation. In addition, ammonia may be found in large quantities in animal buildings. Ammonia is released from manure and urine. In addition, ammonium chloride is used as a nitrogen source in fertilisers. In this study, the atmospheric corrosion of hot-dip-galvanised steel and zinc alloy-coated steel such as zinc–aluminium and zinc–aluminium–magnesium has been studied in atmospheres containing different levels of ammonia. Investigations have also been conducted at different levels of ammonium chloride. The results are discussed in view of the mechanisms of corrosion of zinc and zinc alloy-coated steel in ammonia and ammonium chloride-containing environments.     

Corrosion behavior of porous magnesium coated by plasma electrolytic oxidation in simulated body fluid

Porous magnesium has a great potential to be used as degradable bone scaffolds. In this study, porous magnesium with 35% percolating porosity has been successfully fabricated through powder metallurgy route utilizing space holders. The intrinsic mechanical properties of the porous magnesium were measured by nanoindentation testing and analyzed with the Oliver–Pharr method. Afterward, a ceramic coating on the surface of the porous magnesium was performed by plasma electrolytic oxidation (PEO) treatment in a silicate‐based solution. The morphology and composition results of the PEO coatings indicated that it is possible to apply a homogenous and adhesive ceramic coating layer on all free surface of the porous magnesium through PEO method. The protective performance of the PEO coatings was evaluated using by potentiodynamic polarization and electrochemical impedance spectroscopy tests in simulated body fluid. The results revealed the PEO coating significantly improves biocorrosion resistance of the porous magnesium. Therefore, it can be used as an effective method to control the degradation rate of porous magnesium implants in the human body.     

Electrochemical and theoretical assessment of the effect of two biocides on the corrosion of petroleum steel in sulfur‐polluted Black Sea water

Although the inhibitory effects of different biocides continue to gain ever‐increasing importance, the corrosion inhibition of petroleum steel in the Black Sea water by such compounds remains largely uncharacterized. Thus, to study the effect of sulfate‐reducing bacteria, corrosion parameters in oxygen‐free medium contaminated with sulfur have been determined. The variation of corrosion rates with the addition of two biocides, glutaraldehyde (GA) and ammonium chloride (AC), has been determined by using Tafel extrapolation and linear polarization methods in sulfur‐polluted seawater, both with and without biocides. Overall, this experimental work, also corroborated by theoretical data, reveals that some concentrations of GA and AC act as effective biocides in sulfur‐polluted medium.     

The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn 29Ca 4 alloy

The aim of this study was to investigate the structure and corrosion resistance of amorphous, amorphous‐crystalline, and crystalline Mg₆₇Zn₂₉Ca₄ alloy for biodegradable applications. This paper presents a preparation method and results of the structural characterization and corrosion resistance analysis of the material. Samples were prepared in the form of 3 mm diameter rods. The structure of the alloy was examined with the use of X‐ray diffractometry and scanning electron microscopy. The thermal properties of the samples were examined with differential scanning calorimetry (DSC). Results of DSC analysis were used to determine heat treatment temperatures, allowing to obtain different fractures of crystalline phase in the material. Corrosion resistance of heat‐treated samples was investigated by immersion tests and electrochemical measurements performed in the simulated body fluid. The X‐ray diffraction results confirmed that the prepared Mg₆₇Zn₂₉Ca₄ alloy's structure is fully amorphous. After heat treatment, samples with different fractions of amorphous phase in the structure were obtained. Immersion tests of the samples showed that the structure significantly influenced corrosion resistance in examined materials. It should be pointed out, that certain amounts of crystalline phase in amorphous matrix can greatly improve the corrosion resistance of Mg₆₇Zn₂₉Ca₄ alloy.     

Corrosion and mechanical properties of plasma electrolytic oxidation‐coated AZ80 magnesium alloy

Plasma electrolytic oxidation (PEO) coatings were produced on AZ80 magnesium alloy in a solution containing silicates and phosphates and working at high current densities with short treatment times. The effect of a sealing treatment in boiling water on corrosion and mechanical properties of the coatings were investigated. Moreover, the corrosion mechanism of the samples with and without the sealing treatment was evaluated. The microstructure of the coatings was characterized with scanning electron microscope observation and X‐ray diffraction analysis. The mechanical properties were evaluated with nanoindentation tests and the corrosion resistance was studied by potentiodynamic polarization, electrochemical impedance spectroscopy, and scanning vibrating electrode technique. The results showed that the sealing did not influence the microstructure and the mechanical properties of the samples and instead produced a remarkable increase in the corrosion resistance. The crevice corrosion, present in the sample without the sealing, was avoided with the treatment in boiling water.     

Mg-5Y-3Sm-0.8Ca-0.5Sb合金的高温蠕变行为

采用蠕变实验和理论计算,研究了时效态Mg-5Y-3Sm-0. 8Ca-0. 5Sb合金在250～300℃和50～70 Pa条件下的蠕变行为。结果表明,该合金具有良好的抗高温蠕变性能,其在300℃和70 MPa下的稳态蠕变速率为3. 28×10-8s-1。在50～70 MPa的应力下,当温度由250℃升到300℃时,应力指数由2. 30变为3. 22;在250～300℃的温度下,当应力由50 MPa升到70 MPa时,蠕变激活能由65. 4 kJ/mol变为81. 0 kJ/mol。     

长期堆放氯氧镁水泥合格性检验方法研究

氯氧镁水泥性能与其他水泥不同,而长期堆放未使用的氯氧镁水泥无法用肉眼判断其合格性,因此需要探究一种检测方法对其性能进行检测,进而判定其是否合格可用。通过水泥胶砂法从强度方面进行检验判定,了解其力学性能的同时,可以判定其合格性。