Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Oxides Catalysts of Rare Earth and Transient Metal for Catalytic Oxidation of Benzene

The catalysts of CeO2 and the mixture of CeO2 and CuO were prepared, and the activities of these catalysts for completely oxidizing benzene were studied.The results show that the optimal proportion of CeO2/CuO is 6: 4.The highest temperature at which benzene was completely oxidized on these catalysts at different airspeed was measured.Compared these catalysts with the noble metal used, our catalysts had superiority in the resources and the industrial cost besides good activities.     

现代电弧炉流程钢液氮控制的试验研究

通过生产试验研究了电弧炉冶炼过程、LF精炼过程及连铸过程钢液氮的控制。研究表明，电弧炉冶炼过程主要是电弧区增氮，LF过程及连铸过程钢液增氮主要是钢液与大气接触，LF供电制度也对钢液吸氮有影响。     

Calculation of the Thermodynamic Properties of Diatomic Substances Based on the Ornstein-Zernike Equation

The new method of calculation of intermolecular distribution functions is used to calculate various thermodynamic properties of diatomic substances (oxygen, nitrogen, ethane). Good agreement is demonstrated between the calculation and experimental data.     

Ti,N,Mg对M2高速钢凝固组织和硬度的影响

为了改善Ｍ２高速钢共晶碳化物的分布，本文利用小凝固试样变质的方法研究了Ｔｉ，Ｎ和Ｍｇ对Ｍ２高速钢凝固组织和硬度的影响。试验结果表明，加入Ｔｉ或Ｔｉ－Ｎ后，共晶碳化物形态和分布有很大改善，而加入Ｔｉ－Ｎ后对凝固组织有轻微的细化作用，但只添加Ｔｉ不补碳时，钢的淬火硬度和回火硬度均下降；加入适量的Ｍｇ可以使片状的Ｍ２Ｃ型共晶碳化物转为鱼骨状的Ｍ６Ｃ型共晶碳化物，使其分布有所改善，Ｔｉ和Ｍｇ复合加入可以明     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

土壤因子对植物缺铁失绿的影响

本文主要从土壤 pH ,重碳酸盐 ,和氮素形态等几方面综述了各种土壤因子对土壤缺铁失绿的影响 ,并提出了进一步加强研究的方向     

竖直狭缝通道中液氮沸腾强化换热的实验研究

实验表明，狭缝间隙对液氮自然对流核态沸腾换热有明显的影响，在低热流密度下，间隙小的狭缝沸腾换热比间隙大的狭缝明显增强，当狭缝间隙小于实验压力下气泡的脱离直径时，对于同样的热流密度，传热温差减小一个数量级以上，沸腾换热系数提高十几倍到二十倍以上，当热流密度增加一定程度（＞4W/cm^2)时，间隙小的狭缝沸腾换热比间隙大的狭缝有所减弱。