32位MIPS微处理器中乘法器的设计和实现

在Booth算法的基础上,结合MIPS 4KC微处理器中的流水线结构和乘法器的工作过程,提出了一种改进的Booth乘法器的设计方法,并采用全制定方法实现,用这种方法实现的乘法器单元具有面积小、单元电路可重复性好、版图设计工作量小、功耗低等特点.     

浅谈炼钢车间的自动控制系统

介绍了天津钢铁工业结构调整改造后的新钢铁企业炼钢车间的自动控制系统，系统的配置、主要功能，并对系统做出评价。     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

珠钢不锈钢冶炼技术探讨

本文阐述了不锈钢冶炼的关键技术，为生产准备提供帮助。     

基于SDL的通信软件维护模型SMM

软件维护是软件生存周期的一个重要且花费很大的阶段，维护工作的自动化是软件行业十分迫切的需要。本文提出了一个基于ＩＴＵ－ＴＳＤＬ语言的通信软件维护模型ＳＭＭ。在此模型中，软件维护被分成三个部分：建立面向维护的数据库，制定维护规范和基于功能转换的自动维护。该模型将有助于软件维护支撑环境的建立     

输气管道天然气连续取样器的研制及应用

文章针对国内管输天然气气质分析工作中取样环节所存在的问题，结合国外技术发展趋势，全面地介绍了输气管道天然气连续取样器的研制过程。实践证明，该装置较好地解决了天然气密度值偏差问题，满足管输天然气全分析的要求，同时，该装置的推广应用将会提高天然气的计量准确度。     

A Low-Power Wide-Dynamic-Range Analog VLSI Cochlea

Low-power wide-dynamic-range systems are extremely hard to build. The biological cochlea is one of the most awesome examples of such a system: It can sense sounds over 12 orders of magnitude in intensity, with an estimated power dissipation of only a few tens of microwatts. In this paper, we describe an analog electronic cochlea that processes sounds over 6 orders of magnitude in intensity, and that dissipates 0.5 mW. This 117-stage, 100 Hz to 10 KHz cochlea has the widest dynamic range of any artificial cochlea built to date. The wide dynamic range is attained through the use of a wide-linear-range transconductance amplifier, of a low-noise filter topology, of dynamic gain control (AGC) at each cochlear stage, and of an architecture that we refer to as overlapping cochlear cascades. The operation of the cochlea is made robust through the use of automatic offset-compensation circuitry. A BiCMOS circuit approach helps us to attain nearly scale-invariant behavior and good matching at all frequencies. The synthesis and analysis of our artificial cochlea yields insight into why the human cochlea uses an active traveling-wave mechanism to sense sounds, instead of using bandpass filters. The low power, wide dynamic range, and biological realism make our cochlea well suited as a front end for cochlear implants.     

起重机吊钩拖动绕线电动机他励双高调速系统

本文提出励磁电流可自动控制的他励式双高调速系统设计方案。系统在提升特别是在下放重物时，具有较硬的机械性；在负载１０－１００％的变化范围内，可实现最大偏差Δｎｍａｘ／ｎｍｉｎ１００％≤１０％，调速范围Ｄ≥１０；在满载运行条件下，可节约电能８０％以上。     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

油气集输管道最佳敷设方式的分析

根据大庆油田油气集输工艺设计的实践，分析了几种实用的油气集输管道敷设方式的优缺点。在对不同敷设方式的管道热耗做了较详细计算的基础上，进行了比较，提出了确定油气集输管道的最佳敷设方式：站外管道基本上采用埋地敷设；站内管道则应依据站址处的常年最高地下水位资料来确定，即在保证管道不长期受地下水浸泡的前提下，站内室外管道以埋地敷设为主，室内管道以架空与理地同时敷设为最佳；地下水位高的站内，以架空敷设最佳。