Linear actuation in coextruded dielectric elastomer tubes

Cylindrical fibre actuators have been constructed by a coextrusion method using a thermoplastic polyurethane wall and a conductive grease filler. These actuators may be operated as single fibres or bundled together as actuating ropes. Key results include the validation of Carpi’s wall pressure model [F. Carpi, D.D. Rossi, Dielectric elastomer cylindrical actuators: electromechanical modelling and experimental evaluation, Mater. Sci. Eng. C-Biomimetic Supramol. Syst. 24 (2004) 555–562] and the proof-of-concept demonstration of a technique that can be used for producing inexpensive dielectric elastomer actuators on an industrial scale.     

改良BBS法评价聚氨酯发泡催化剂

改良BBs法用光电法测发泡高度-时间曲线,用机械手完成投掷钢球动作,过程用微机控制。本文对此法测得的三乙胺、四甲基乙二胺、二甲基乙醇胺、双(二甲基氨基乙基)醚、三乙烯二胺等催化剂在聚氨酯软质泡沫塑料形成过程中的胶化-发泡曲线进行了讨论,并评价了它们的催化特性。改良BBs法与手工BBs法相比,具有检测精度高,样本采集点多的优点。     

直埋玻璃钢聚氨酯保温管及其保温层厚度设计

介绍了直埋玻璃钢聚氨酯保温管的结构形式及优良性能．为了降低玻璃钢聚氨酯保温管的初期投资,探讨了直埋玻璃钢聚氨酯热力管保温层的2种设计方法,并采用工程实例进行计算．结果表明,按双层保温计算法设计保温层更为经济合理．以上结论为直埋玻璃铜聚氨酯保温管保温层设计提供了理论依据．     

Reduction of Noise from Disc Brake Systems Using Composite Friction Materials Containing Thermoplastic Elastomers (TPEs)

Attempts have been made for the first time to prepare a friction material with the characteristic of thermal sensitive modulus, by the inclusion of thermoplastic elastomers (TPE) as viscoelastic polymeric materials into the formulation in order to the increase the damping behavior of the cured friction material. Styrene–butadiene–styrene (SBS), styrene–ethylene–butylene–styrene (SEBS) and nitrile rubber/polyvinyl chloride (NBR/PVC) blend system were used as TPE materials. In order to evaluate the viscoelastic parameters such as loss factor (tan δ) and storage modulus (E′) for the friction material, dynamic mechanical analyzer (DMA) were used. Natural frequencies and mode shapes of friction material and brake disc were determined by modal analysis. However, NBR/PVC and SEBS were found to be much more effective in damping behavior. The results from this comparative study suggest that the damping characteristics of commercial friction materials can be strongly affected by the TPE ingredients. This investigation also confirmed that the specimens with high TPE content had low noise propensity.     

凝胶渗透色谱研究水性聚氨酯乳液

通过凝胶渗透色谱（GPC）研究了不同加料方法、不同扩链剂、不同聚酯对乳液分子量的影响；结果表明：不同扩链剂合成的乳液数均分子量的次序为：BD／DEG〈NPG〈BD〈DEG〈DEG／TMP；不同聚酯合成的乳液的数均分子量大小次序为：CMA-44—600〉T1136〉CMA-1000〉MX785〉CMA-44。     

聚氨酯/蒙脱土纳米复合弹性体材料--(Ⅱ)结构及性能的表征

借助锥体磨的研磨剪切外力，将聚醚多元醇插层进入蒙脱土片层中，使其片层间距扩大并发生部分剥离，从而利用本体插层聚合法制备了综合性能优异的聚氨酯／蒙脱土纳米复合弹性体材料。当有机蒙脱土添加量仅为1％时，其拉伸强度比纯聚氨酯弹性体高30％．达到30．2MPa，断裂伸长率也略有增加。TGA及吸水实验分析表明聚氨酯／蒙脱土纳米复合材料有更高的热失重温度和更低的吸水率．研究了蒙脱土含量对聚氨酯／蒙脱土纳米复合材料各项性能的影响。     

聚氨酯基pH/温度敏感性水凝胶的结构形态

通过阴离子型端丙烯酸酯基聚氨酯(UAA)与N-异丙基丙烯酰胺(NIPAAm)的共聚交联反应,制备了pH/温度敏感性水凝胶,分析了水凝胶的结构形态及溶胀水的状态.结果表明,凝胶相结构均匀,随聚氨酯含量的降低,凝胶的骨架变得松散,并且孔道结构增大,导致溶胀凝胶中不可冻结水含量及凝胶强度的降低.     

硬质聚氨酯泡沫塑料用于冷库保温工程施工中应注意的问题

阐述了冷库现场喷涂聚氨酯施工作业中对原材料、施工队伍、施工工艺等方面的要求和建议。     

CaSO4晶须补强增韧聚氨酯弹性体复合材料力学性能的研究

研究了CaSO4晶须含量以及界面粘合状态对聚氨酯弹性体力学性能的影响,并初步分析探讨了CaSO4晶须补强增韧的机理。结果表明,CaSO4晶须质量含量为5％－10％左右的复合材料具有最佳的力学性能。晶须经硅烷偶联剂预处理后,能大幅度提高复合材料的强度和韧性。其补强增韧机制主要为应力传递。