Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.     

Set methods of left-turn waiting zone at signalized intersection

To maximize the number of vehicles passing by the stop-line in a cycle and improve the operation efficiency of intersection in China,the settlement of left-turn lane waiting-zone is becoming prevailing. Based on conflicting-point method,the internal mechanism of left-turn flow after stopping line was analyzed through taking postposition left-turn lane waiting-zone intersection for instance. The relationship between the first left-turn vehicle and the last vehicle of previous phase passing the conflicting point was expounded. According to the time of successive arriving of two vehicle flows at conflicting-point,the reasonable layout for waiting area of left-turn vehicles was researched when the clearance index was less than 0. The results suggest that the appropriate layout for waiting area of left-turning vehicles can improve the operation efficiency of intersections.     

关于体育教学改革的问题探讨

分析体育课教学中的主要任务、教材内容、教学方法、成绩考核等几个问题,并对此进行初步的研究和探讨,提出改革意见和措施,以改善体育课的教学效果。     

声参数的高性能混凝土强度推定模型

为研究高性能混凝土的声波传播特性及实现其强度的快速、准确、无损检测,基于超声波检测方法,应用嫩江、多宝山附近的沙石料,对高性能混凝土对声波的扩散性及其抗压性能与声参量之间的模型关系进行了研究.建立了高性能混凝土抗压强度与声速之间的多种数学模型.通过实测检测数据进行验证,满足精度要求.高性能混凝土的非均质性降低,其抗压强度与声速相关性较好,用超声的方法完全可以实现强度的快速推定.同时,也为将来高性能混凝土地区强度推定曲线的建立奠定了研究基础.     

应力吸收层沥青混合料的低温抗裂性能

通过对自主研发的Sampave等3种改性沥青结合料和不同级配的应力吸收层沥青混合料进行低温弯曲和低温蠕变试验,分析沥青结合料和矿料级配对应力吸收层沥青混合料低温抗裂性能的影响.结果表明:自主研发的Sampave特种改性沥青混合料具有优良的低温抗裂性能,但单一改性剂SBR改性沥青并不能达到应力吸收层沥青结合料的性能要求;矿料4.75 mm、0.075 mm筛孔通过率对其低温抗裂性能影响较敏感.     

加氢降凝组合工艺技术

抚顺石油化工研究院开发的生产低凝清洁柴油加氢降凝组合工艺,集加氢精制与临氢降凝工艺技术优点于一体,具有工艺流程简单、精制及降凝效果好、柴油收率高、原料适应能力强、产品方案灵活等特点,已在哈尔滨等炼油厂得到工业应用.     

Performance analysis for range expansion in heterogeneous networks

In this paper, the uplink and downlink performance of a two-tier heterogeneous network （HetNet） with range expansion （RE） is analyzed. Different from previous works, base stations （BSs） are modeled as a spatial Poisson point process. This model can not only capture the irregularity of the BS deployment but also lead to closed form expressions. With the analytical results, the impacts of several key parameters on the coverage and throughput performance are investigated. Our results justifies the effectiveness of RE and Pico deployment. Based on our analyses, certain attention should be made on the RE design to balance the uplink and downlink performance. Our analyses are corroborated by simulations and can thus serve as a flexible and quick guidance for system design without complicated and time-consuming system-level platform construction and simulation.     

2-（4-氯苯氨基）甲基苯酚降解的动力学研究

采用高效液相色谱技术,开展了Fenton试剂对2-（4-氯苯氨基）甲基苯酚（CMP）的氧化降解动力学的研究。考察了初始双氧水摩尔浓度、亚铁离子摩尔浓度和温度等因素对CMP降解速率的影响,结果表明,当双氧水摩尔浓度、亚铁离子摩尔浓度增大和温度升高时,CMP的氧化速率明显加快。在30~45℃的温度范围内,其氧化降解符合假一级反应动力学模型,反应的表观活化能Ea为102.90kJ/mol。     

抽真空截止点的位置对压铸件气孔的影响

在真空压铸中 ,抽真空截止点的确定对压铸件的品质影响很大 ,过早和过迟将影响压铸的连续生产和不利于减少铸件的气孔。抽真空截止点应设在冲头快压射前 15～ 2 0mm处 ,真空压铸可以提高铸件的密度 1%以上。     

Atomic force microscopy study of biaxially oriented polypropylene films

Atomic force microscopy (AFM) uses a very sharp pointed mechanical probe to collect real-space morphological information of solid surfaces. AFM was used in this study to image the surface morphology of a biaxially oriented polypropylene film. The polymer film is characterized by a nanometer-scale, fiberlike network structure, which reflects the drawing process used during the fabrication of the film. AFM was used to study polymer-surface treatment to improve wettability by exposing the polymer to ozone with or without ultraviolet (UV) irradiation. Surface-morphology changes observed by AFM are the result of the surface oxidation induced by the treatment. Due to the topographic features of the polymer film, the fiberlike structure has been used to check the performance of the AFM tip. An AFM image is a mixture of the surface morphology and the shape of the AFM tip. Therefore, it is important to check the performance of a tip to ensure that the AFM image collected reflects the true surface features of the sample, rather than contamination on the AFM tip.