农药残留分析样品前处理技术新进展

介绍了近年来农药残留样品前处理技术的新进展,并对此进行了评述和展望。     

Alkaline fuel cells: contemporary advancement and limitations

ZeTek Power recently introduced mass manufacturable and cost effective alkaline fuel cells on the market. Today's research is focused on further improvement both in terms of performance increase and cost reduction. This research is classically performed using small (4 cm²) experimental electrodes in the half-cell configuration. This allows the primary electrochemical losses in an anode or cathode to be determined independently. Additional performance losses occur when one integrates large electrodes into a module of 24 cells and in a stack comprised of many modules. By comparing the performance of half-cell experiments to that of modules, these losses can be distinguished and addressed. The information thus obtained, both for the small electrodes and in up-scaling is vital if one is to identify the key areas in which improvement is possible and where to focus future research. Furthermore, the identification of the losses in a module and system allows us to predict the final performance from half-cell measurements of a new laboratory scale experimental electrode.     

Surface Preparation of Tantalum for Encapsulation and Adhesive Bonding

A number of methods of surface preparation of tantalum for encapsulation in silicone rubber and for structural adhesive bonding were explored. The only ones which could be generally useful were boiling for 24 hours in distilled water (28% improvement) or boiling for 4 hours in 20% sodium hydroxide solution followed by boiling for 2 hours in dilute hydrochloric acid (34% improvement). An alternative, which could sometimes be used, was heating in air for at least 2 hours at 100°C.     

高效防腐中温磷化液LC-1的制备及性能

制备了一种含Zn2+、Mn2+、N i2+三系离子的LC-1磷化液,通过硫酸铜点滴、氯化钠浸蚀、SEM等手段对磷化膜进行了测试,测定了磷化温度、磷化时间对膜层耐蚀性的影响。结果表明,在磷化温度大于65℃,磷化时间大于10 m in的条件下,所形成的磷化膜结晶均匀、致密、黑褐色,耐蚀性良好。LC-1三系磷化液可适用于大批量钢铁工件的磷化生产。     

宽温耐硫变换催化剂制备工艺研究

利用催化剂活性评价、催化剂活性组分含量测定、Ｘ—光衍射等手段，研究了共浸法制备宽温耐硫变换催化剂制备工艺过程中载体氧化铝的吸水率、浸渍条件、煅烧温度等对催化剂性能的影响。     

ZrO2载体催化剂的制作及特性探讨

选择有应用价值的CuO/ZrO2体系，通过大量试验寻找到了一种以ZrO2为载体的高比表面催化剂的制备方法。     

集成电路密封用高纯邻甲酚醛环氧树脂的制备

ECN树脂中的可水解氯含量是决定树脂质量的—个重要指标。本文研究了反应温度、ECH/OCN配比、反应时间和碱用量等因素的影响,取得了规律性的认识,并获得最佳配方,制备出高纯度的ECN树脂系列产品。     

非金属电镀用导电漆的研制

介绍了导电漆、作为导电填料的片状镀银铜粉的制备工艺流程。分别研究了漆膜表面单位电阻与镀银铜粉的含量及其粒径以及钛酸酯偶联剂的含量之间的关系。结果表明,当镀银铜粉的粒径为400目、质量分数在57%~65%之间,钛酸酯偶联剂的质量分数为10%时,所得涂膜的导电性能最佳。加入含C-18的油酸可以使导电漆长期贮存而电阻值不变。经检测,所得涂膜具有良好的性能:附着力1级,硬度1 H,柔韧性1 mm,冲击强度50 kg/cm2,膜厚10~15μm,漆膜表面每厘米电阻0.15Ω,每分米电阻0.47Ω。指出了导电漆应用过程中的注意事项。     

微晶纤维素增粘剂的研制

以棉浆为原料，废盐酸为水解催化剂，所得合成革用微晶纤锥素增粘剂的质量指标达到了德国和日本同类产品的标准。     

考试综合管理信息系统的关键技术研究

基于.NET技术成功开发了考试综合管理信息系统,针对考试管理工作面临的问题,提出了相应的解决方案,并以此为依据介绍了该系统开发过程中的自动编排算法、安全策略等关键技术。该系统已成功运用,并解决了高校日益复杂的考务管理工作。