From product-oriented to process-oriented: Emerging new engineering paradigm

The conventional approach has put emphasis upon reducing labour, and increasing efficiency and uniformity. But this holds good only in the mass production paradigm. As we are entering the age of small production with far wider varieties, these principles of yesterday should be re-examined. Labour itself sometimes gives satisfaction if it involves the joy of creation, and longer time does not necessarily mean just patience, it sometimes turns into expectation if greater joy will be provided later. Too much fitness for the purpose sometimes means lack of robustness and adaptability to the quickly and widely changing environment. Thus, we should reconsider the items we thought important in the mass production age to aptly cope with the diversification of each customer’s requirements.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

钛对耐硫变换催化剂性能的影响

利用常压微反色谱、程序升温还原（ＴＰＲ）等技术研究了钛对耐硫变换催化剂性能的影响，结果表明：（１）钛能明显提高耐硫变换催化剂的活性，尤其是在低于６２３Ｋ时活性提高最为明显；（２）工业侧流试验后，含钛样品的保留活性及活性保留率均高于Ｋ８－１１；（３）催化剂中添加助剂ＴｉＯ２后，能显著提高对原料气中Ｈ２Ｓ含量变化的适应能力，因此可以拓宽对原料气的选择范围，对工业生产有着十分重要的现实意义。     

光外差系统噪声等效功率的一种测量方法

本文介绍了利用工作于Bragg衍射的Ge晶体声光调制器作为外差系统中的频移器来测量外差系统的噪声等效功率(NEP)的方法。该方法具有测试系统简单、信号光功率、偏频可调的优点。实验测试与理论分析吻合。     

基于移位原理的顺序控制器研究

本文根据PLC顺序控制程序的设计思路,阐述了用常用集成数码移位寄存器、电力电子开关电路和少量外围电子元件构成移位控制器的原理,根据此设计思路制作的移位控制器经过在实验室环境下运行,证明了设计方案的可行性。     

Spectral Feature Analysis of Semiconductor Thin Disk Laser

The semiconductor thin disk laser is a new type of semiconductor laser. This work gives the basic operation function of the semiconductor disk laser, and analyses the heat effect by the experimentally measured photoluminescence spectrum of the laser chip at different pump power and different temperatures. We can see that: with increasing pump power, the thermal effect of the gain material becomes seriously and causes the saturation of carrier lifetime, so the electron-hole pair created in the absorbtion lay...     

高频等参数感应(ВИКИЗ)测井技术应用

介绍了高频等参数感应的基本原理。以胜利油田比较典型的 3口井为例 ,详细分析了高频感应资料在划分薄夹层、确定储层流体饱和类型、评价储层电阻率空间分布等方面的应用。研究结果表明 ,高频感应具有极高的纵向分辨率和较好的径向探测特性 ,能够准确计算地层真电阻率、侵入带电阻率及侵入半径 ,通过与常规感应及薄层测井资料的对比 ,论证了高频等参数感应在测井技术应用上的优越性     

一种适用于高数据速率和高速移动环境的新型信道估计方法——双正交通道信道估计方法

本文给出了一种适用于高数据速率和高速移动环境下的新型有效的信道估计方法-双正交通道信道估计方法(CETOC,Channel Estimation by using Two Orthogonal Channels),这种信道估计方法通过采用两个独立通道的联合估计,可以有效的克服快衰落的影响,从而使得在快衰落信道下应用多维状态调制成为可能.     

Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

高频地波雷达相位补偿系统

OSMAR2000采用的是“一发八收,收发共用”模式的相控阵高频地波雷达.为了扩大其探测的范围,在新的雷达系统中将采用多发多收的模式,从而导致当信号通过通道后,信号的相位会因受到通道的调制而发生改变,使得雷达无法正常工作,因此需要对通道的相位进行实时监控和补偿.在参考了低频段的相位测量原理和射频段的相移电路的设计理论的基础上,该文提出了基于差分放大器、容阻和容感器件的高频地波雷达收发通道的相位控制系统.