A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

织构对铟凸点剪切强度的影响

制作了2种形式的铟凸点：即直接蒸发沉积的铟柱和将铟柱回流得到的铟球。同时对比了铟柱和铟球2种凸点的剪切强度，测试结果表明铟球剪切强度为5.6MPa，铟柱的剪切强度为1.9MPa，前者约为后者的2.9倍。对铟凸点微观结构的X光衍射分析发现：铟柱剪切强度低是织构弱化所致；铟球剪切强度高是由于回流破坏了铟柱的理想（101）丝织构模式，从而提高了铟球的剪切强度。     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

一种基于GE90-30PLC的飞剪自动控制系统

本文介绍了调整线材轧线精轧机前专用于切头的启停式飞剪的自动控制系统。该系统以GE90—30PLC为控制核心，辅以热金属HMD、光电编码器等元件，能很好地完成飞剪的剪切及定位。其中着重阐述了飞剪控制中各个重要参数的计算原理和方法。     

基于延迟捕获功能的血液切变率测量方法

对延迟捕获的基本原理进行了系统的分析,详细介绍了利用延迟捕获功能实现计时计数法测量转速的具体方法和实例.此方法已应用在粘度测试仪器中切变率指标的测量上,经实际使用表明具有软硬件结构简单、成本低、精度较高、运行可靠等优点,对于一些在嵌入式应用中需要测量转速指标时,可谓一种良好的方法.     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

水闸闸室化算梯形横截面上不平衡剪力的分配计算

当地弹性地基梁法计算非岩石地基的水闸底板应力时，首先要求解出不平衡剪力，当闸墩截面选择梯形时（主要是边墩），常用方法是作图法，这既有误差又繁琐。所以就此推导出一个公式，可直接求解平衡剪力。     

圆杆弹性和弹—塑性扭转公式的探讨

对圆杆在线弹性阶段，弹－塑性阶段和全塑性阶段的扭转剪应力的计算公式作了分析，并推导了在材料的应力－应变关系（τ－γ关系）不服从虎克定律时，扭转真实剪应力的计算公式。文中对扭转强度计算公式的来源，物理含义及其都作了详细的说明。这对执行和理解国家ＧＢ１０１２８－８８《金属室温扭转试验方法》是有益的，而且对高校中材料力学的教学具有一定的参考价值。     

Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.