一种耐超高温、耐酸聚合物的制备及性能测试

摘要：为解决常规聚合物无法满足超高温深井酸化压裂的技术要求，本文分别以丙烯酰胺（AM） 甲基丙烯酰氧乙基三甲基氯化铵（DMC）、AM DMC SMA（十八烷基甲基丙烯酸酯）为原料，通过自由基聚合制备出两种耐酸聚合物SY-1和SY-2，并对其结构进行表征及性能测试。结果表明：SY-2红外谱图中720 cm-1为—(CH2)n—的弯曲振动吸收峰，单体成功接枝到聚丙烯酰胺分子链上；热重分析表明，SY-1升温至600℃失重比为98%，SY-2失重比86%，热稳定性得到改善；质量分数为20%盐酸中，SY-2质量分数0.8%：180℃，170s-1流变性能测试，SY-2剪切终点黏度56mPa?s，90℃、120℃、150℃剪切1h，黏度为83.6mPa?s、43.5mPa?s、27.8mPa?s，剪切稳定性分别为85.66%、74.45%、52.01%； 180℃、3MPa条件下，静态酸岩反应速率为8.94?10-5(g/cm2?s)，较常规SY-1反应速率1.69?10-4(g/cm2?s)减小一个量级。且与缓蚀剂、铁离子稳定剂配伍性良好，克服高温酸化压裂技术的应用瓶颈。     

Electrodiffusion diagnostics of the flow and mass transfer inside a network of crossing minichannels

The global mass transfer and the local flow structure inside a set of crossing minichannels were characterized using the electrodiffusion method. The individual square-cross channel sections (a = 1.5 mm in sides) intersect at right-angles in order to form the flow cell. An array of 39 circular platinum electrodes (0.25 mm in diameter) was flush-mounted into the wall of the flow cell to investigate the wall shear rate at different locations. This array of small sensors allowed characterization of longitudinal and lateral variations in wall shear rate across the flow cell, flow distribution at the inlet and outlet sections, transition between laminar and turbulent flow regimes, and flow behaviour at the channel crossings. The results of global wall mass transfer measurements demonstrated that, from a mass transfer point of view, the flow cell exhibits similar behaviour to a porous medium.     

Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

环氧-聚酰胺体系中增韧剂的研究

在环氧-聚酰胺体系中分别加入“海岛结构”QS-1、聚硫橡胶、液体丁腈橡胶增韧改性,通过对固化物剪切强度、弯曲弹性模量及断裂强度的对比,“海岛结构”QS-1增韧综合性能较好.     

垂直管内弹状气泡上升中壁面传递的实验研究

垂直管内弹状流壁面传递是诸多工业应用中需研究的重要问题之一。今用极限扩散电流技术,对弹状气泡上升时瞬时壁面剪应力和传质系数进行了测定,结果显示:当基于表观气速的Froude数FrG < 0.74时,壁面剪应力随弹状气泡和液塞的到来呈现方向相反的交替变化,壁面传质系数亦相应变化;而当FrG > 0.74时,剪应力方向一直向下,说明液膜向下流动,且弹状气泡和液塞的到来对壁面传质系数的影响很小。这说明下落液膜射流穿透了液塞段,控制了整个壁面传递过程。研究还对下落液膜区、尾迹区及液塞段的不同传递特征及机理进行了分析, 并结合气泡塔熔融结晶器中弹状气泡上升时的传热,对结晶操作条件的合理选择进行了讨论。     

Measurement of Adhesive Bond Properties Including Damage by Dynamic Mechanical Thermal Analysis of a Beam Specimen

A method to obtain mechanical properties using a bonded (double) cantilever beam (or three point bend) specimen loaded in a manner to produce pure shear in the adhesive layer is reviewed. A revised mathematical solution which allows for easier interpretation of optimum beam dimensions to the one originally developed by Moussiaux, Cardon and Brinson for the static case is presented. An extension of this solution for a fixed/fixed viscoelastic beam under steady state oscillations developed by Li, Dickie and Morman is also discussed. Previous results using a vibrating beam to determine the complex viscoelastic properties of a bonded beam are reviewed. These results demonstrate conclusively that dynamic mechanical thermal analysis (DMTA) measurements discriminate differences in surface treatments and various environmental conditions. New measurements are presented that indicate the DMTA procedure can be used to quantify damage simulated by imbedded flaws in beams. The procedure is also shown to assess the effects of both humidity and corrosive environments on lap specimens. It is suggested that this technique may ultimately provide a method to quantify the amount of hidden damage in an adhesive joint subjected to fatigue, moisture or corrosive environments.     

Shear creep resistance of styrene–isoprene–styrene (SIS)‐based hot‐melt pressure‐sensitive adhesives

The effects of the properties of substrates and tackifier on the shear creep of SIS‐based HMPSAs were investigated. The holding power (t_b) and shear adhesion failure temperature (SAFT) were measured. The relationship between the complex viscosity and the holding power was examined. The holding power and SAFT values of the triblock SIS blends were higher than those of the diblock‐containing SIS blends, perhaps because blends using triblock SIS have higher crossover temperature and complex viscosity than those using diblock‐containing SIS. Higher levels of aromatic resin‐modified aliphatic tackifier and rosin ester were found to decrease the holding power of the HMPSAs. This maybe due to the fact that rosin ester and aromatic‐modified aliphatic resin are compatible with both the ends and midblocks of SIS. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 825–831, 2006     

High PVC film‐forming composite latex particles via miniemulsification,part 1: Preparation

Miniemulsification technology was used to encapsulate TiO₂ particles inside a styrene/n‐butyl acrylate copolymer with high loading levels (11 to 70% PVC (pigment volume concentration)). In this approach, a St/BA copolymer dissolved in toluene in the presence of a costabilizer (hexadecane) was mixed with a dispersion of TiO₂ particles in toluene and sonified, and then emulsified in an aqueous surfactant solution by sonification. The effect of sonification time on both the dispersibility of the TiO₂ particles in the presence of the copolymer and hexadecane and on the encapsulated particle size was investigated. Particle size analysis by dynamic light scattering showed that these composite latexes are quite stable. It was also found that as the TiO₂ loading increased from 11 to 43% PVC, the particle size of the TiO₂ dispersion decreased while the polymer‐encapsulated TiO₂ particle size increased. The effect of surfactant concentration (sodium lauryl sulfate, SLS) on the encapsulated particle size was investigated using four different SLS concentrations in the 11% PVC system. The results showed that as the SLS concentration increased the particle size decreased, as expected. Also it was found that the minimum surfactant concentration that gives stable encapsulated TiO₂ particles is above 10 mM SLS. The role of HD in the recipe was studied for an artificial latex containing no TiO₂ and one prepared at 11% PVC, in terms of particle size before and after solvent stripping, and its effect on the T_g. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4504–4516, 2006     

电晕法处理超高相对分子质量聚乙烯纤维

用电晕法对超高相对分子质量聚乙烯纤维进行了表面处理。利用DPPH检测纤维表面自由基的产生和变化，并用XPS表面元素分析、SEM等方法探讨了纤维表面性能处理前后的变化。实验发现，通过电晕处理后，纤维复合材料的抗剪切强度从未处理的5．98MPa提高到14．3MPa。     

Novel pyridinium photoinitiators and their applications for the ultraviolet crosslinking of acrylic pressure‐sensitive adhesives

The demand for ultraviolet (UV)‐crosslinkable pressure‐sensitive adhesives (PSAs) has rapidly been increasing. A variety of different PSAs containing new photoreactive pyridinium derivatives have been evaluated for their effectiveness in improving adhesion and cohesion in UV‐crosslinkable PSAs. PSAs have been evaluated with respect to the tack, peel adhesion, and shear strength. This article summarizes the breakthrough technology used to achieve better performances in UV‐crosslinkable acrylic PSAs. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007