DC-DC电荷泵的研究与设计

以Dickson电荷泵的基本原理为出发点，研究了一种将正电压输入转为负电压输出的开关电容电路。由于开关电容的充放电特点，为确定电容时间常数，采用非交叠时钟控制信号避免了由于时钟交叠而造成的当电容充电还未完成即对下一级电容进行放电的现象。同时，参考功率MOS-FET的电容模型通过增大驱动电路的电流减小了开关管的上升延时，提高了开关动作的速度，使转换效率得到明显提高。此电路结构简单，性能优良，易于集成，可广泛应用于输出负电压的电源产品中。     

氯气泵叶轮连续破碎原因

针对YLJ型液环式氯气泵叶轮在短期内频繁破碎的情况,对其破碎原因进行了分析,并提出相应的改进措施,使烧碱工艺系统保持了长、满、安、稳的运行状态。     

英台地区天然水驱油藏的开发特点及稳产技术

掌握边底水运动规律，控制并利用活跃的边底水能量，是成功开发天然水驱油藏的关键。英台地区的英台、四方坨子和一棵树等三个油田均为天然水驱油藏，天然能量充足。油藏投入开发后初期含水较高，含水上升极快，造成产油量大幅度递减。针对其开发特点，适时采用大泵、电潜泵提液强采，通过大量补孔层间接替以及加密调整和扩边等稳产技术措施，确保了油藏以3％-5％的采油速度长期稳产，水驱采收率高达50％以上。     

Optimum thermoeconomic and thermodynamic performance characteristics of an irreversible three-heat-source heat pump

The coefficient of performance and specific heating load of an irreversible three-heat-source heat pump are given by using a general cycle model affected by the finite-rate heat transfer, heat leak and internal irreversibility of the cyclic working fluid. The heat pumping load divided by the total cost per unit time is taken as a new objective function and used to investigate the performance of the heat pump. The thermoeconomic and thermodynamic performance characteristics of the heat pump are discussed in detail. Some important performance parameters such as the thermoeconomic objective function and coefficient of performance are optimized. The optimally operating regions of the heat pump and the bounds of several performance parameters are determined. Finally, it is pointed out that the Carnot heat pump may be taken as a special case of a three-heat-source heat pump and consequently its optimal performance can be directly derived from the results obtained here.     

液氨装置工艺计算及改造总结

介绍我公司液氯装置由活塞式氨气压缩机氨-CaCl2盐水系统改为带经济器的螺杆式氯气液化机组的工艺计算,新建装置特点以及改造后的装置在我公司运行情况和使用效果。经改造后的液氯装置每年可节约电费73万余元,同时提高了装置的安全可靠性。     

双柱塞砂浆泵中工作机构的设计和仿真研究

本文介绍了双柱塞砂浆泵的工作原理，根据机构替代原理建立起双柱塞砂浆泵工作机构的运动分析模型，然后在MatLab环境下，详细介绍了工作凸轮曲线的设计程序，利用计算机设计程序可以方便地分析工作缸活塞以及工作凸轮机构的位移、速度、加速度，利用SIMULINK仿真工具箱进行运动学仿真，为工作机构设计提供相应的理论分析依据。     

基于ADμC834芯片热泵热水机组控制器的研制

热泵热水机组是一种新型热水和供暖产品,它可以从空气、水等环境中吸取能量,热效率高,被公为是传统锅炉、电热水器及燃油(气)热水机组的更新换代环保型产品。详细阐述了以ADμC834芯片为核心的热泵热水机组控制器软硬件系统设计。论述了多路温度数据与压力数据采集、液晶显示等模块的硬件组成及各个模块的工作原理。控制器的软件系统采用前后台架构,用QuickStart平台开发完成。其人机界面系统由按键阵列和TG2401286V2型液晶显示屏组成。     

地面驱动螺杆泵恒液面控制方法

恒液面控制有利于提高泵效,降低抽油杆柱和泵等设备的失效率。为此结合地面控制装置,研究了一种控制方法和软件。该软件根据控制装置实时测量的转速、扭矩等参数并结合地层开采能力、杆泵型号等参数,分析计算出液面高度和控制范围,并计算出转速改变量,由控制装置实行闭环控制。经大庆油田5口井试验表明,液面高度误差均在50 m内,实现了螺杆泵恒液面控制目的。     

Calculation methods for comparing the performance of pure and mixed working fluids in heat pump applications

Three methods for comparing cycle performance of working fluids, pure as well as non-azeotropic mixtures, are investigated for two applications and for two mixture pairs, HCFC22-CFC114 and HCFC22-HCFC142b, and their pure components. The methods differ in the way of calculating the heat exchange processes. They assume, respectively, equal minimum approach temperatures, equal mean temperature differences and equal heat transfer areas. Changes of coefficient of performance (COP) with composition are explained for all methods. It is shown that transport properties must be taken into account when making rigorous comparisons between working fluids. To predict the relations between fluids with high accuracy, one must use the method with equal heat transfer areas. By the method with equal mean temperature differences, the COP can be estimated with the same accuracy for mixtures as for pure fluids, and can be used for rough estimations of the COP level with different fluids. The method of equal minimum approach temperatures should be avoided for non-azeotropic mixtures.     

NUMERICAL STUDY ON QUASI- STEADY FLOW OF NONNEWTONIAN FLUID IN SUCK-ROD PUMP

This paper presents a numerical method for simulation of the flow and thecalculated results of the quasi-steady axisymmetrical flow field and pressure distribution on valveball with power-law model for Non-Newtonian fluid in suck-rod pump.We believe the methodcan provide a foundation for further research and improvement of the design of suck-rod pump.