Zr对Cu—Zn—Al形状记忆合金相变的影响

采用示差扫描热分析(DSC)、X射线衍射及透射电镜,研究了Zr对Cu-Zn-Al合金高温相变、马氏体正逆转变以及形状记忆效应的影响。结果表明,添加Zr0.35wt-％时,能有效地抑制α,γ相析出,促进β_2→DO_3→18RM转变。(M_s-M_f)及(A_s-A_f)温度区间较窄,马氏体相变激活能最低,马氏体变体间界面的可动性好,形状记忆效应最佳。     

Investigation on gradient material fabrication with electron beam melting based on scanning track control

A new electron beam control system was developed in a general vacuum electron beam machine by assembling with industrial control computer, programmable logic control （PLC）, deflection coil, data acquisition card, power amplifier, etc. In this control system, scanning track and energy distribution of electron beam could be edited off-line, real-time adjusted and controlled on-line. Ti-Mo gradient material （GM） with high temperature resistant was fabricated using the technology of electron beam melting. The melting processes include three steps, such as preheating, melting, and homogenizing. The results show that the GM prepared by melting technology has fine appearance, and it has good integrated interface with the Ti alloy. Mo and Ti elements are gradually distributed in the inter.face of the gradient material. The microstructure close to the Ti alloy base metal is α ＋ β basket-waver grain, and the microstructure close to the GM is a single phase of β solid solution.     

Binary blends of polyethers with fatty acids: A thermal characterization of the phase transitions

A series of binary blends of poly(ethylene oxide) (PEO), poly(propylene oxide) (PPO), and polytetrahydrofuran (PTHF), characterized by similar average molecular weights, with selected fatty acids (capric acid, lauric acid, myristic acid, palmitic acid, and stearic acid) were prepared by melt mixing. Differential scanning calorimetry was applied to characterize the phase transitions of melting and crystallization, and a synergistic effect was found to occur for PEO/fatty acid blends, as evidenced by the values of the enthalpy of the phase transition. This effect was probably due to hydrogen bonding between PEO and the fatty (carboxylic) acids, which facilitated the formation of crystalline structures; an analysis of IR spectroscopy data showed a shift in the absorption bands of OH groups. The morphology development of the PEO/carboxylic acid blends, as observed with polarizing light microscopy, could be described as spherulitic growth with spontaneous selection of the lamellar thickness. The textures of the individual fibrils, consisting of stacks of several tens of lamellae corresponding to PPO and PTHF, were less regular than the texture of PEO and showed large macroscopic heterogeneity. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 861–870, 2003     

Characterization of the thermal properties of PLA fibers by modulated differential scanning calorimetry

Polylactide (PLA) has been melt spun to produce multifilament continuous yarns. The thermal characteristics of PLA filaments have been investigated using modulated differential scanning calorimetry (MDSC). With MDSC, it is possible to separate the different thermal events and to analyze them more precisely. The influence of hot drawing on thermal properties of PLA filaments has been studied. Hot drawing promotes an increase of glass transition temperature (T_g) and a decrease of heat capacity. The cold crystallization spreads on a larger range of temperature and the peak occurs at a lower temperature. The initial degrees of cristallinity of PLA filaments have been calculated thanks to the reversing and non reversing curves of MDSC. Tensile properties of PLA filaments are also investigated.     

Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Use of laser scanning confocal microscopy for characterizing changes in film thickness and local surface morphology of UV-exposed polymer coatings

Laser scanning confocal microscopy (LSCM) has been used to characterize the changes in film thickness and local surface morphology of polymer coatings during the UV degradation process. With the noninvasive feature of LSCM, one can obtain thickness information directly and nondestructively at various exposure times without destroying the specimens or deriving the thickness values from IR measurement by assuming uniform film ablation. Two acrylic polymer coatings were chosen for the study, and the physical and chemical changes of the two systems at various exposure times were measured and analyzed. Those measurable physical changes caused by UV exposure include film ablation, formation of pits and other surface defects, and increases in surface roughness. It was found in both coatings that changes in measured film thickness by LSCM were not correlated linearly to the predicted thickness loss using the changes in the CH band obtained by the Fourier Transform Infrared (FTIR) spectroscopy measurements in the later degradation stages. This result suggested it was not a uniform film ablation process during the UV degradation. At later stages, where surface deformation became severe, surface roughness and profile information using LSCM were also proven to be useful for analyzing the surface degradation process Presented at the 81st Annual Meeting of the Federation of Societies for Coatings Technology, November 13–14, 2004 in Philadelphia, PA.     

Improvement of polymer blend properties by changing sequence of mixing

The basic objective of this article is to improve the polymer blend properties by changing mixing sequence. Blending of two elastomers does not lead to a molecularly homogeneous blend (true solution), but to a heterogeneous system in which both polymer phases are present. In this article, the detailed study of heterogeneous distribution of carbon black as well as blend inhomogenity and the physicomechanical including dynamic mechanical properties of the blend has been carried out. The choice of the blend was natural rubber/polybutadiene rubber as 85:15. Heterogeneous carbon black distribution study was also performed in differential scanning calorimeter. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2735–2742, 2007     

Crystallization behavior of dry‐brush PEO‐PS block copolymer and PEO homopolymer blend

The crystallization behavior of semicrystalline PEO homopolymer/triblock PS‐PEO‐PS copolymer blend system, which exhibited “Dry‐Brush” in the melt. A symmetric polystyrene–poly(ethylene oxide)–polystyrene triblock copolymer was blended with PEO homopolymer (h‐PEO) having the same molecular weight as that of the PEO block in the copolymer. Considering the composition of the blend (W_ps ≥ 0.8), PEO spheres were formed in the blend. Because of the dry‐brush phase behavior of this blend, h‐PEO added was localized in the PEO microdomains, which increases the domain size without changing the microdomain morphology. The crystallization of PEO block was confined within the microdomains and the crystallization temperature was about 60°C lower than normal. Self‐seeding tests were performed to clarify the nucleation mechanism of the blend. Because the droplets size varies greatly, multicrystallization peaks were witnessed in the self‐seeding process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A novel approach for fit analysis of thermal protective clothing using three-dimensional body scanning

The garment fit played an important role in protective performance, comfort and mobility. The purpose of this study is to quantify the air gap to quantitatively characterize a three-dimensional (3-D) garment fit using a 3-D body scanning technique. A method for processing of scanned data was developed to investigate the air gap size and distribution between the clothing and human body. The mesh model formed from nude and clothed body was aligned, superimposed and sectioned using Rapidform software. The air gap size and distribution over the body surface were analyzed. The total air volume was also calculated. The effects of fabric properties and garment size on air gap distribution were explored. The results indicated that average air gap of the fit clothing was around 25–30 mm and the overall air gap distribution was similar. The air gap was unevenly distributed over the body and it was strongly associated with the body parts, fabric properties and garment size. The research will help understand the overall clothing fit and its association with protection, thermal and movement comfort, and provide guidelines for clothing engineers to improve thermal performance and reduce physiological burden.     

Bi2—xPbxSr2Ca2Cu3Oy系高Tc超导体相变的研究

用DSC研究了高T_e超导体B_(2-r)Pb_rSr_2Ca_2Cu_sO_v(x=0,0.2,0.4,0.6)从室温至600℃范围内的相变。在320℃和440℃附近有二个吸热蜂,每一个峰对应一个相变过程。440℃附近的相变是不可递的,其原子激活能为1.37eV,是由高T_e相向低T_e相的转变。而320℃附近的相变则与超结构的形成有关。