Calculated hardenability for improved consistency of properties in heat treatable engineering steels

Hardenability is one of the most important parameters controlling the heat treated properties of engineering steels. It affects the consistency of response for microstructure, hardness, strength, toughness, and dimensional change (distortion). This study illustrates that a major benefit of controlling hardenability is improving the consistency of dimensional distortion resulting from heat treatment. To facilitate the supply of steels to hardenability limits, especially restricted hardenability, a new technique was developed for the prediction of Jominy hardenability from chemical composition. The technique, termed the “Database Method,” uses measured Jominy hardenability and chemical composition data, contained in a database, to calculate the hardenability for a query composition. Using up to ten known steels, selected from the database with compositions closely matching that of the query steel, a small adjustment is made to the measured hardenability of each known steel allowing for the small difference in composition between the query and chosen steel. The final calculated result for the query steel is taken as the average of the various estimates. The basis of the Database Method is explained, and the advantages are illustrated for selecting engineering grades.     

钛制容器产品试板压弯角度的探讨

针对钛制容器产品试板弯曲角度按现行标准执行中出现的问题，从力学角度进行探讨，导了了试板压弯对所采用的压头直径与试板厚度和延伸率的关系，即Ｄ〉（１／δ－１）ｔ，并提出了设定试板弯曲压头直径的新思路。     

无垫片焊接密封法兰计算方法的讨论

应用华脱尔斯法建立了内、外焊唇焊接法兰结构的力学模型,在相同设计条件和材料状况下,进行了内、外焊唇结构法兰的受力分析、设计计算和结构尺寸对比。笔者认为:如果设计计算成立且焊接条件允许,内焊唇结构的法兰比外焊唇结构的法兰螺栓载荷减小,截面积减少,法兰直径和厚度也相应大幅降低。     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

用直接纺丝法制芳纶短纤维

研究了直接纺丝制取芳纶短纤维的新方法。讨论了纤维长度、直径及力学性能与纺丝条件的关系。发现影响纤维长度的主要因素是空气层高度和喷丝速度,影响纤维直径的主要因素为喷口直径及喷丝速度。此外,还用PPTA短纤维制成了均匀的PPTA"浆粕"纤维。     

Effect of Mode of Drying on Microstructure of Potato

Potato v. Irga was subjected to blanching, and thereafter was dried by convection, puff-drying, and freeze-drying. Microstructure of raw, blanched, and dried tissue was analyzed under the light microscope using computer image analysis. It was found that the tissue of the investigated variety is built up from cells much smaller than those described in literature for other cultivars. Blanching caused starch gelatinization and increase of cross-sectional area of cells. There was no evidence of broken cell walls. Convective drying resulted in cell shrinkage and some breaking of cell walls. It was estimated that some 12% of cells lost integrity during drying. Limited disintegration of the tissue caused by convective drying is attributed to small size of cells, large contact area, and high cohesive forces between cells. Puff-drying damaged the tissue much more than the convective drying. The most devastating to tissue microstructure was freeze-drying, probably freezing per se.     

短纤维直径对橡胶复合材料性能的影响

制备了 3种具有不同直径、相同长径比及其分布的涤纶短纤维增强氯丁橡胶基复合材料。对屈服强度及伸长率、断裂强度及伸长率以及撕裂强度等力学性能的研究发现 :在相同长径比及其分布情况下 ,与传统混合法则不同的是屈服强度和伸长率不相等 ,也不是只取决于短纤维的直径 ,而是受直径和长度的共同作用 ;在相同的纤维体积分数时 ,复合材料的断裂强度基本相同 ,而断裂形变和撕裂强度随纤维直径的减小而增大     

釜用机械密封的安装及故障分析

针对石油化工釜用机械密封中常出现的故障进行分析 ,并提出了改进措施 ,以便使机械密封更好地发挥作用 ,杜绝化工设备存在的跑、冒、滴、漏现象 ,即改善了环境 ,又节约了能源。     

两步法合成大粒径丁苯胶乳

研究了聚甲基丙烯酸甲酯（MMA）对丁苯（BS）胶乳的附聚作用以增大丁苯胶乳粒径；探讨了无机盐、体系pH值及体系中MMA胶乳与BS胶乳的固含量比（R值）对附聚后丁苯胶乳的粒径及稳定性的影响。结果表明：适当添加无机盐可以稳定胶乳体系，最佳用量（质量分数）为0．1％～0．2％；适当增大体系pH值，可增大胶乳粒径；在附聚过程中，当R值在两个附聚峰附近时，可增大丁苯胶乳的粒径。     

分子筛催化剂波面移动床传热特性研究

采用粉粒体传热的两区模型和微元体能量平衡理论 ,研究和分析了不同颗粒粒径的分子筛催化剂对波面移动床换热器各传热系数的影响。实验结果表明 :分子筛催化剂颗粒粒径的大小对壁面传热系数和总传热系数影响大 ,而对中央区的传热系数无影响。