Volatile compounds in oils after deep frying or stir frying and subsequent storage

Soybean oil (900 g) was heated by deep frying at 200°C for 1 h with the addition of 0, 50, 100, 150 and 200 mL water, and then stored at 55°C for 26 weeks. Soybean oil, corn oil and lard were heated by stir frying and then stored at 55°C for 30 weeks. The volatiles and peroxide values of these samples were monitored. All samples contained aldehydes as major volatiles. During heating and storage, total volatiles increased 260-1100-fold. However, aldehyde content decreased from 62–87% to 47–67%, while volatile acid content increased from 1–6% to 12–33%; especially hexanoic acid which increased to 26–350 ppm in the oils after the storage period was completed. Water addition to the oils heated by deep frying tended to retard the formation of volatile compounds. The total amount of volatile constituents of lard heated by stir frying increased more during storage than that of corn oil or soybean oil. Peroxide values did not reflect the changes of volatile content in the samples.     

On the Predominant Electron-Donicity of Polar Solid Surfaces

The reasons for the predominant electron-donicity of almost all solid polar surfaces and its implications are discussed in this paper. By contact angle or interfacial tension measurements, the electron-accepting as well as the electron-donating properties of polar liquids can be ascertained, through the interplay between their energies of adhesion and cohesion. For the solid-liquid interface, direct interfacial tension measurements are not possible, but indirectly, solid/liquid interfacial tensions of polar systems can be obtained by contact angle measurement. However, as the energy of cohesion of a solid does not influence the contact angle formed by a liquid drop placed upon its surface, one can only measure the solid surface'ks residual polar property, manifested by the energy of adhesion between solid and liquid. This residual polar property is of necessity the dominant component; in most cases this turns out to be its electron donicity. When, by means of contact angle measurements with polar liquids, both electron-accepting and electron-donating potentials are found on a polar solid, it is most likely still partly covered with a polar liquid: usually water. The amount of residual water of hydration of a polar solid follows from its polar (Lewis acid-base) surface tension component (γ^AB). The degree of orientation of the residual water of hydration on a polar solid can be expressed by the ratio of the electron-donating to electron-accepting potentials (γ^⊖/γ^⊕), measured on the hydrated surface.     

改性皂土催化下甲苯的浓硝酸硝化(Ⅶ)

在皂土硝酸盐催化下，甲苯能被浓硝酸对位选择性硝化，对邻硝化产物比率达１．０以上。     

NBR／EPDM的增容共混研究

本文采用第三组份增容途径,改善了NBR/EPDM并用胶的相容性、加工性和力学性能。通过对不同增容体系的研究对比,发现不同增容剂的增容效果差异很大,其巾以EVA-14增容效果最为显著,加入该增容剂的并用胶,在适当的工艺条件及硫化体系下,可获得最佳力学性能。本文还研究了不同增容剂对并用炭黑胶各种性能的影响,可以做到在不降低并用胶的力学性能的同时,提高并用胶的耐热空气老化、耐大气老化和耐臭氧老化性能.透射电镜实验和动态力学谱图证明了加与未加增容剂时,NBR/EPDM并用胶均为两相结构,增容剂起表面活性剂的作用,加强了两相界面间的相互作用,使分散相EPDM细微化和均匀化。     

聚丙烯酸钾与腐植酸复合高吸水性树脂的合成研究

以腐植酸与丙烯酸聚合制备了高吸水性树脂,讨论了交联剂、引发剂以及KOH用量对聚丙烯酸与腐植酸高吸水性树脂吸水率的影响,结果显示在n(MBA)∶n(AA)=0.0005、n(KPS)∶n(AA)=0.0075、n(KOH)∶n(AA)约为0.70、温度为80℃的条件下合成时,其吸水倍率可达到最优值。而且在接近自然条件下(35℃)失水速度慢,保水时间可达100 h以上,重复吸水性能好。运用红外光谱分析了腐植酸与丙烯酸的反应机理。     

移动agent在远程医疗诊断系统中的应用

随着网络技术的发展,作为一种新的分布式计算模式,移动agent已经成为当前的一个研究热点。介绍了移动agent的相关技术,并利用移动agent的技术优势,针对远程医疗诊断系统的现状,提出了一个基于移动agent技术的远程医疗诊断系统的设计,并给出了具体的思路和解决方案,较好地解决了远程医疗诊断中智能性、灵活性等问题。     

Selective Oxidation of Methanol to Formaldehyde Using Modified Iron-Molybdate Catalysts

Methanol selective oxidation to formaldehyde over a modified Fe-Mo catalyst with two different stoichiometric (Mo/Fe atomic ratio = 1.5 and 3.0) was studied experimentally in a fixed bed reactor over a wide range of reaction conditions. The physicochemical characterization of the prepared catalysts provides evidence that Fe₂(MoO₄)₃ is in fact the active phase of the catalyst. The experimental results of conversion of methanol and selectivity towards formaldehyde for various residence times were studied. The results showed that as the residence time increases the yield of formaldehyde decreases. Selectivity of formaldehyde decreases with increase in residence time. This result is attributable to subsequent oxidation of formaldehyde to carbon monoxide due to longer residence time.     

前大油田注水系统防腐防垢技术的研究

前大油田注水系统腐蚀、结垢问题十分突出,开发了适用于前大油田注水水质的JYSJ-Q型杀菌剂、JYHZJ-Q型缓蚀阻垢剂,并通过试验确定了配套加药工艺.经现场应用,有效缓解了注水系统的腐蚀结垢问题,获得了显著的社会效益及经济效益.     

In situ leaching method for determination of chloride in concrete pore water

In the in situ leaching (ISL) method, pore water ionic content is determined in small cavities drilled in mortar/concrete specimens. Prior investigations have demonstrated the ISL applicability to obtain pH and nitrite ion concentration in concrete/mortar pore water. The application of the method is extended here to determine pore water chloride ion concentration (and pH) within practical test times in mortars and concretes prepared in the laboratory and in concrete cores extracted from a bridge deck in deicing salt service. Spatial resolution for the determination of composition profiles is also illustrated. Modeling of the ISL process indicates that chloride binding accelerates the approach toward a terminal cavity concentration, reducing test duration to practical lengths for moderate permeability concretes. This acceleration can be attributed to maintaining a higher gradient of free chloride near the cavity wall due to the release, during leaching, of previously bound chloride. Consequently, there is a faster chloride buildup in the cavity water compared with the no-binding case. Experimental chloride and pH results obtained by the ISL test in mortar samples show good agreement with those from the pore water expression (PWE) method. Also, examples are presented of application of ISL data to obtain chloride binding isotherms, and pore water chloride to hydroxide ratio relevant to assessing conditions for corrosion of steel reinforcement. The ISL method presents a less costly and less disruptive alternative to PWE for pore water analysis. It is noted, however, that in a few instances ISL could not be implemented because of excessive absorption of cavity water by the surrounding medium.     

含氮氧化物(NOx)废气的处理方法

介绍了氮氧化物废气的产生原理、处理方法,并结合某厂硝化废气处理装置改造过程的实例,对加压水吸收处理氮氧化物废气的方法做了详细介绍,同时将该法与其他处理方法进行了比较.