The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn 29Ca 4 alloy

The aim of this study was to investigate the structure and corrosion resistance of amorphous, amorphous‐crystalline, and crystalline Mg₆₇Zn₂₉Ca₄ alloy for biodegradable applications. This paper presents a preparation method and results of the structural characterization and corrosion resistance analysis of the material. Samples were prepared in the form of 3 mm diameter rods. The structure of the alloy was examined with the use of X‐ray diffractometry and scanning electron microscopy. The thermal properties of the samples were examined with differential scanning calorimetry (DSC). Results of DSC analysis were used to determine heat treatment temperatures, allowing to obtain different fractures of crystalline phase in the material. Corrosion resistance of heat‐treated samples was investigated by immersion tests and electrochemical measurements performed in the simulated body fluid. The X‐ray diffraction results confirmed that the prepared Mg₆₇Zn₂₉Ca₄ alloy's structure is fully amorphous. After heat treatment, samples with different fractions of amorphous phase in the structure were obtained. Immersion tests of the samples showed that the structure significantly influenced corrosion resistance in examined materials. It should be pointed out, that certain amounts of crystalline phase in amorphous matrix can greatly improve the corrosion resistance of Mg₆₇Zn₂₉Ca₄ alloy.     

Binary Ti–Fe system. Part I: Experimental investigation at high pressure

The present work illustrates the effect of quasi-hydrostatic pressure on the positions and widths of the homogeneity ranges of the intermetallic phases TiFe and TiFe₂ at high temperatures. The experiments were performed with Ti–Fe diffusion couples that were heat treated in a multi-anvil press at 2.5 GPa. The solubility limits of the phases were derived from the concentration profiles that were measured using electron probe microanalysis. It was found that the homogeneity ranges of TiFe and TiFe₂ extend to higher titanium concentrations, if the pressure is applied. The positions of the phase boundaries of the intermetallics on the iron-rich side are not affected by the pressure. The accuracy of the experimental data including the homogeneity ranges and temperatures was verified by comparing the homogeneity ranges of β-Ti(Fe), α/δ-Fe(Ti) and γ-Fe measured in this study with the homogeneity ranges taken from literature. The pressure was calibrated using the pressure-induced phase transitions of bismuth.     

Corrosion behavior of Cu–Sn bronze alloys in simulated archeological soil media

The corrosion behavior of synthetic Cu–Sn bronze alloys with six different Sn contents was examined through an electrochemical test and a synthetic test in a simulated corrosive medium. The mechanism of corrosion and the morphology of the corroded surfaces were characterized through field emission scanning electron microscopy equipped with energy-dispersive spectroscopy. At the corrosion potential, the corrosion behavior appears to be determined by the charge transfer step and the diffusion process. It was found that the bronze-IV (Cu–26.8Sn) specimen exhibited the best corrosion resistance, as evidenced by a low corrosion current density and a high impedance. This improvement resulted from an increase in the content of the Cu–Sn solid solution in the alloy, which was conducive to forming a relatively more protective passive film on the surface of the bronze alloy. This finding would be valuable in the anticorrosion protection of archeological artefacts after their excavation.     

Modelling consumer choice through the random regret minimization model: An application in the food domain

In line with findings on post-purchase food-choice regret, one can expect that pre-purchase anticipated regret with respect to forgone (non-chosen) alternatives has an impact on consumer food choices, especially when the choice is considered to be important. The traditional Random Utility Maximization (RUM) models for discrete choices may not fully capture this impact. This study investigates the usefulness and potential in the food domain of a discrete choice model that follows the regret minimization principle, the Random Regret Minimization (RRM) model, as an alternative and complement to existing RUM models. The two models are applied to consumer stated choices of cheese in a choice experiment. The study also investigates whether and to what extent a number of personality traits determine whether particular consumers rather choose according to utility-maximization, or regret-minimization principles. Results show that at the aggregate level the two models have a similar goodness of fit to the data and prediction ability. Still, each of them shows better fit for particular subgroups of consumers, based on personality traits. Hence, the present study reveals a potential for the RRM model applications in the food domain, and adds to the empirical literature supporting previous findings on the RRM model found in other contexts. Further research is needed to explore in which situations and for which consumer segments the RRM model is the most useful model.     

分层注水井智能测试调配技术试验评价

注水井智能测试调配技术在不改变原注水管柱的基础上，利用井下可调式堵塞器，通过地面电脑控制，实现了测试调配同步进行。通过7口井的现场试验及分析评价，表明该工艺具有测调精度高、测调时间短、测试资料准确等特点。     

机械-射流破岩耦合特性研究

在现代旋转钻井破碎井底岩石中仍是以机械破岩为主，理论与实践证明，射流辅助破岩是提高钻井破岩效率的重要途径，但它们的耦合特性研究极少。文章基于渗流场与应力场的耦合理论分析，进行了机械与射流破岩耦合特性的实验研究。结果表明：射流压力和水楔作用对岩石渗流场、应力场具有重要作用，耦合作用比非耦合作用的破岩效率有较大幅度的提高。在实验条件下，砂岩的耦合作用提高破岩效率40％左右，灰岩的耦合作用提高破岩效率20％左右。     

CO2吞吐工艺操作参数的整体优化设计

针对ZY油田原油CO2吞吐的工艺过程，建立了CO2吞吐数值模拟模型。应用数值模拟方法对CO2吞吐进行了实例分析，首先对该井的CO2吞吐参数进行了单因素敏感性分析，分析了CO2周期注入量、注入速度、焖井时间、采液速度等因素对CO2吞吐效果的影响。在此基础上进一步运用正交试验方法对CO2吞吐参数进行了优化，通过计算表明用正交试验优选法得到的优化方案比单因素敏感性分析所得的优化结果更为合理。     

对CFG桩质量缺陷的探讨

根据具体工程的概况及水文地质条件，分析了CFG桩在地下水位出现大面积缩颈现象和复合地基载荷试验达不到设计要求的原因，并介绍了地基补强措施，以满足工程质量的要求。     

基于Matlab的雷达试验数据分析处理系统

针对雷达外场试验中的需求,提出了基于Matlab软件平台的数据分析处理系统。该系统能很好地完成雷达录取数据的精度分析、威力分析和各种显示图形的绘制,并且在实际中得到了应用。