标准化钻速法检测地层压力技术的改进与应用

利用钻井资料检测地层压力的方法，基本上都是以泥岩的压实规律为基础，以钻速的变化为根据的。但是在钻井过程中影响钻速的因素很多，可以衡量一种检测方法优劣，主要是看其能否合理、全面地考虑诸多影响因素，能否适用于现场。本文介绍标准化钻速法检测地层压力的基本原理和工作步骤，提出了适用于现场的改进的数学模型和应用方法，并与实测值很接近。     

导向钻井系统在多目标大井斜定向井中的应用

详细介绍了C-D井在钻进过程中井眼轨迹的控制过程,总结了在C-D井中使用导向钻井系统的成功经验。用1根导向马达、2套钻具组合、3只牙轮钻头顺利地完成了定向、增斜、稳斜及降斜,7个目标点一次击中,且最小靶心距仅0.99m。用15d完成了这口斜深2287.09m、井斜58.40°、水平位移903.11m的多目标定向井,钻穿目标点之多、实钻井眼剖面符合率之高、施工难度之大、速度之快,在目前国内都处于领先地位。     

预测井眼稳定性的力学化学耦合方法

在井眼力学稳定性评价的基础上，将硬脆性页岩水化后岩石强度等参数的变化规律用于页岩水化前后坍塌压力变化的对比分析，结果表明，地层坍塌压力当量密度随页岩水化程度的增加逐渐升高。给出了预测井眼稳定性的力学化学耦合方法，并将该方法应用于现场生产中，取得了较好的预测效果     

A Low-Power Wide-Dynamic-Range Analog VLSI Cochlea

Low-power wide-dynamic-range systems are extremely hard to build. The biological cochlea is one of the most awesome examples of such a system: It can sense sounds over 12 orders of magnitude in intensity, with an estimated power dissipation of only a few tens of microwatts. In this paper, we describe an analog electronic cochlea that processes sounds over 6 orders of magnitude in intensity, and that dissipates 0.5 mW. This 117-stage, 100 Hz to 10 KHz cochlea has the widest dynamic range of any artificial cochlea built to date. The wide dynamic range is attained through the use of a wide-linear-range transconductance amplifier, of a low-noise filter topology, of dynamic gain control (AGC) at each cochlear stage, and of an architecture that we refer to as overlapping cochlear cascades. The operation of the cochlea is made robust through the use of automatic offset-compensation circuitry. A BiCMOS circuit approach helps us to attain nearly scale-invariant behavior and good matching at all frequencies. The synthesis and analysis of our artificial cochlea yields insight into why the human cochlea uses an active traveling-wave mechanism to sense sounds, instead of using bandpass filters. The low power, wide dynamic range, and biological realism make our cochlea well suited as a front end for cochlear implants.     

起重机吊钩拖动绕线电动机他励双高调速系统

本文提出励磁电流可自动控制的他励式双高调速系统设计方案。系统在提升特别是在下放重物时，具有较硬的机械性；在负载１０－１００％的变化范围内，可实现最大偏差Δｎｍａｘ／ｎｍｉｎ１００％≤１０％，调速范围Ｄ≥１０；在满载运行条件下，可节约电能８０％以上。     

Introduction to geothermal exploration on ascension island, South Atlantic Ocean

The exploration for a geothermal resource on Ascension Island utilized a strategy that initially employed geologic mapping. On the basis of this, subsurface faults were mapped using an aeromagnetic survey. The faults were then explored using electrical resistivity surveys to define areas of potential hydrothermal fluid up-welling. The results of all of these techniques were used to site temperature gradient holes. A deep geothermal exploration well was then drilled in the area with highest heat flow adjacent to a rhyolite-to-trachyte volcanic complex.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

提高大直径井眼机械钻速的几项措施

随着我国西部地区石油勘探开发的进展，5000－7000m的深探井所钻数量不断增多，套管程序增加，特别是大尺寸井眼所钻深度明显加大。由于国产大尺寸钻头结构单一、型号少，破岩机械能量和水力能量不足，在易斜井段目前尚无可靠的防斜保直措施，以及钻井液性能不适宜等原因，大尺寸井眼的钻这远远低于215．9mm井眼的钻速。据此，提出了几项可以提高大尺寸井眼钻速的措施：增加大尺寸钻头的种类，采用阶梯式扩眼钻头，强化钻井参数和水力参数，选用中速动力钻具，改善钻井液性能以及采用冲击旋转钻具等。     

潜油电动机滑行时间的自动测量

潜油电动机滑行时间是评定电动机装配质量的重要指标。鉴于手工测量电动机滑行时间存在效率低和误差较大的不足,设计了潜油电动机滑行时间自动测量系统。它通过分压电路和计算机自动测量系统测量潜油电动机定子上感应的电压变化状况,即可得到电动机滑行时间。用手工测量、波形分析和自动测量3种方法测量6种型号电动机的滑行时间,其中5种滑行时间长于3s,判定为合格;1种滑行时间短于3s,判定为不合格。3种方式测量的滑行时间具有较好的一致性,仅波形分析法得出的滑行时间比自动测量的滑行时间稍长,表明自动测量方法的精度和重复性可满足要求。     

引黄五座泵站火灾自动报警及联动控制系统

介绍了引黄工程五座泵站的火灾自动报警系统的组成及功能，对泵站的火灾探测系统、报警系统、联动控制系统、灭火系统、控制台等原理进行了详细说明，供同行参考借鉴。