辐射剂量对环氧树脂电子束固化行为的影响

分析了电子束剂量对环氧树脂体系辐射固化行为的影响规律。研究结果表明，电子束辐射过程中，温度由树脂辐射体系表面向内部逐渐降低，随着辐射剂量提高，树脂体系温度上升，辐射表面与内部的温度梯度加大，高辐射剂量下的温度变化缓慢。树脂辐射固化层厚度以及在相同厚度的固化程度均随辐射剂量增加，但增幅逐渐变小，树脂辐射固化度沿固化深度会加速下降。     

Investigation of the relationships between the chain organization and rheological properties of atactic poly(vinyl alcohol) hydrogels

The structure and rheological behavior of atactic poly(vinyl alcohol) (a-PVA) hydrogels prepared by freeze/thaw cycles were investigated as a function of polymer concentration and number of freeze/thaw cycles. The presence of phases with different mobilities was observed using ¹³C CP/MAS and DP/MAS NMR experiments. The degree of crystallinity of the a-PVA-rich phase was determined by ¹H NMR free decay experiments. Measurements of the shear storage and loss modulus were performed at a fixed frequency of 1 Hz and a strain value of 0.1%, i.e. under conditions where the deformation imposed on the gel structure is entirely reversible. Results thus obtained showed that an increase in the number of freeze/thaw cycles induces an increase in the degree of crystallinity in the polymer-rich phase together with an increase in the storage modulus. The a-PVA hydrogels became more fragile as the number of freeze/thaw cycles was increased. Moreover, both the percentage of protons in a rigid environment measured by ¹H NMR and the storage modulus values tended to a limiting value after six freeze/thaw cycles. These results show that the first five or six freeze/thaw cycles play a very important role in determining the hydrogel structure and rheological properties. A more detailed comparison of NMR and rheological data led to the conclusion that the storage modulus is mainly controlled by the a-PVA crystallinity while the hydrogen bond interactions have a much smaller contribution.     

咪唑封端扩链脲改性环氧树脂E-51/酸酐MTHPA体系性能研究

以端羟基聚环氧丙烷1000，甲苯二异氰酸酯（TDI），2－甲基咪唑为原料，合成了扩链脲TI，利用DSC，动态热机械分析仪DMA，冲击试验机及扫描电镜（SEM）等手段对TI改性的环氧树脂E－51／甲基四氢化邻苯二甲酸酐（MTHPA）固化体系的反应活性，动态力学行为，冲击性能，断裂面形态结构进行了系统研究，结果表明，改性后的E－51／MTHPA体系反应活性明显提高，固化反应峰顶温度较未改性体系降低160℃－200℃，固化反应的表观活化能由未改性体系的160．3kJ/mol降至63kJ/mol-87kJ/mol，同时与未改性体系相比，经过改性的环氧树脂固化体系冲击强度有较大的提高，在TI含量为5％时体系的玻璃化转变温度Ts达到最高，各改性体系冲击断面呈韧性断裂。     

茂名石化PE农用薄膜专用料的生产和开发

概述了我国农用薄膜现状与发展趋势，分析了存在的问题，对茂名石油化工公司的聚乙烯农用薄膜专用树脂的生产和开发提出了建议。     

Anhydrous esterification of myristic acid with propylene: Ion exchange resin and acid-treated clay as catalysts

Anhydrous esterification of myristic acid with propylene was carried out in the temperature range of 110–145°C and pressure from 190–195 psig in the presence of Amberlyst-15 (cation exchange resin) and Filtrol-24 (acid-treated clay) as catalysts. The product ester, isopropyl myristate finds use in cosmetic and topical medicinal preparations where good absorption through the skin is desired. Filtrol-24 is the catalyst of choice, and the recommended operating temperature is 130°C with a pressure of 190 psig.     

Synthesis of oleyl oleate as a jojoba oil analog

Synthesis of a wax ester analog of jojoba oil was accomplished from oleic acid and oleyl alcohol with a zeolite as catalyst. A full 2³ factorial design at two levels has been used in the synthesis. The variables selected were temperature, reduced pressure and initial catalyst concentration. The most important variable within the range studied was temperature. Reduced pressure had a negative influence, and initial catalyst concentration showed a positive influence on the process. A response equation has been determined for the yield of ester. The properties of the synthesized product are similar to those of natural jojoba oil.     

The effects of glycol methacrylate as a dehydrating agent on the dimensional changes of liver tissue

The dimensional changes of liver sections during the course of processing with glycol methacrylate (GMA) or with ethanol are described. Tissue processing with ethanol served as a control. During prolonged processing steps (24 h each), linear shrinkage of tissue specimens dehydrated with GMA at room temperature was 13.2%. Subsequent infiltration with GMA resulted in trivial swelling, and polymerization in slight shrinkage (2.3%). In comparison, processing with cold GMA resulted in shrinkage during dehydration (about 10.8%), a slight swelling in pure GMA, followed by shrinkage during polymerization (2.2%). Short routine processing schedules resulted in similar shrinkage/swelling patterns, although precise values differed slightly. In all experiments, ethanolic dehydration resulted in smaller dimensional tissue changes than did GMA dehydration. The dimensional changes of tissue sections during stretching on water, mounting and drying compensated for the major part of the shrinkage manifested during processing.     

阳离子交换树脂铁中毒的复苏研究

软化器中使用的阳离子交换树脂容易受到铁离子的污染。采用均匀设计的方法,利用回归分析和最优化技术,研究了复苏剂中各组分对阳离子复苏效果的影响,得出了最佳复苏配方,开发出了一种新的复苏方法。这种方法具有腐蚀性低和复苏效果良好的特点,为生产现场树脂的复苏提供了有益的借鉴。     

空心微珠改性硬质聚氯乙烯复合材料的应用研究

经过改性的超细空心微珠可以作为填料加入到硬质聚氯乙烯（PVC－U）树脂中，同时改善PVC树脂的流变性、冲击性能和刚性等性能。研究结果表明，超细空心微珠加入到硬质PVC管材中，可以明显改善PVC硬管的加工流动性能，显著缩短塑化时间，降低最大扭矩。而超细空民微珠加入到硬质PVC板材时，可以提高PVC硬板的冲击性能，减小制品的收缩率，赋予PVC硬板优异的耐腐蚀性能，且产品的各项性能均符合PVC板材国家标准GB／T4454－96。     

J-199热熔胶膜的研制

讨论了不同VA含量不同熔体指数的EVA和各种增粘剂对热熔胶膜耐热性、软化点、剪切强度、拉伸强度、剥离强度等性能的影响。通过采用不同材料试验和配方的筛选，研制出一种90℃剪切强度0．07MPa、拉伸强度0．47MPa、耐热性好、粘接强度高的热熔胶膜，从而拓宽了热熔胶的使用范围。