硫脲型整合树脂在分析上的应用 Ⅰ.岩样中微量银的中子活化分析

前言银和其他贵金属元素一样,在地壳中比较稀少,按其自然丰度为第67号元素,平均含量仅0.07 ppm。由于地质样品成分非常复杂,为测定其微量银,必须进行严格的化学分离。但是迄今文献中报道的许多分离分法,步骤都相当冗长,一般采用氯化银反     

Thermal degradation of cinnamoylated poly(vinyl alcohol)

Thermogravimetry and pyrolysis in combination with gas chromatography and infrared spectroscopy were the experimental techniques applied to the thermal degradation of cinnamoylated poly(vinyl alcohol) samples, constituted from vinyl alcohol-vinyl cinnamate photocrosslinkable copolymers. The thermal decomposition products include gases, liquids and solids. The gases are formed from saturated and unsaturated volatile hydrocarbons C₁? C₄, carbon monoxide and carbon dioxide. The liquid fraction includes aromatic hydrocarbons and some oxygenated organic compounds. The solid product identified in the greatest amount was cinnamic acid. The content in the thermal decomposition products varies considerably both with copolymer composition and temperature.     

苯基荧光酮分光光度法测定聚烯烃树脂中的钛

应用苯基荧光酮 -聚乙烯醇 -Tween -80显色体系测定了聚烯烃树脂中的钛 ,建立了测定聚烯烃树脂中钛离子的灵敏、快速的分析方法。考察了测定条件 ,在测定过程中 ,以抗坏血酸还原作用消除了Fe3+ 、V5+ 等干扰。配合物最大吸收波长为 5 3 5nm ,其表观摩尔吸光系数ε =1 0× 10 5L/ (mol·cm) ,线性范围为 0～ 0 12 μg/ml。合成试样回收率为 97 3 %～ 10 1% ,相对标准偏差不大于 1 63 % ;加标回收率为 99 95 %～ 10 1 3 % ,该方法选择性高 ,准确性好 ,简便易行     

超强吸水树脂的吸水性能研究

对自制的超强吸水树脂的吸收性能进行了研究，分别考察了吸水树脂的粒径，溶液的pH值，几种离子如Na^ ,K^ ,Ca^2 ,Mg^2 等的水溶液对吸水树脂吸收性能的影响。实验结果表明，在pH为6－8，树脂粒径为100mesh-120mesh时，树脂的吸水性能最好，各种离子对吸水树脂吸收性能的影响大小顺序为：Na^ ＜K^ ＜Mg^2 ＜Ca^2 。     

一步法合成松香改性酚醛树脂

探讨了一步法合成松香改性酚醛树脂的反应机理，确定了最佳原料组成及合成工艺，由此制备出高溶解粘度和矿油容纳度的松香改性酚醛树脂，是一种性能优异的高级胶印油墨连接料     

双马来酰亚胺树脂体系的固化反应研究

利用ＤＳＣ及原位ＦＴＩＲ技术研究了双马来酰亚妥树脂体系的固化反应，获得了在固化反应过程中各组分的转化率与时间的关系，结合热分析数据，确立了最佳固化工艺。     

Synthetic resins: XV. Chelation ion exchange properties of 2,4- dinitrophenylhydrazone of resacetophenone-formaldehyde resin

A number of copolymers were synthesised by condensing the 2,4-dinitrophenylhydrazone of resacetophenone with substituted benzoic acids/ phenols and formaldehyde in the presence of sodium hydroxide or hydrochloric acid. The decomposition temperature, solubility and viscosity of the polymers have been determined. The ion-exchange properties have been studied by using a batch equilibrium method. The distribution of a number of metal ions between an aqueous solution and the resin have been measured. A wide range of pH and variable ionic strengths have been investigated.     

Facile optical resolution of amino acid esters via hydrolysis by an industrial enzyme in organic solvents

Racemic amino acid esters were optically resolved via hydrolysis in organic solvents by the catalysis of an industrial alkaline protease, “Alcalase”. The products which were composed mainly of L-amino acids were insoluble and easily separated by filtration. The activity of the enzyme and enantiomeric excess of the products were significantly dependent on the nature of solvent and the water content in the reaction media. Generally, high values of enantiomeric excess were obtained at low water contents. Many natural and unnatural amino acids were resolved by this method.     

稀土树脂相分光光度法研究

在HCl—KCl(pH0.5)介质中,稀土—三溴偶氮胂二元络合物能较好地被阴离子交换树脂吸附。RE_2O_8在0～8μg/25ml范围内符合比尔定律,以双波长等吸收点法(测量波长λ_1=650nm,参比波长λ_2=740nm)扣除树脂背景影响,应用于稀土矿中稀土总量测定,结果令人满意。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.