Emulsifying Properties of the Total Fraction and the Hydrophobic Fraction of Bovine Milk Proteose-peptones

Since proteose-peptone is a mixture of heterogeneous proteins and peptides, its functional properties have not yet been fully understood. The present study was undertaken to elucidate the emulsifying properties of proteose-peptones and a parallel evaluation was performed of the emulsifying activity of the total fraction prepared from bulk skimmed milk by precipitation with ammonium sulphate and of the most hydrophobic fraction purified by hydrophobic interaction fast protein liquid chromatography. A turbidimetric technique was used and the absorbance value at 500 nm was then directly used as the emulsifying activity index. The results obtained confirmed the good emulsifying activity of this protein fraction of the whey and demonstrated the considerable influence of the concentration on the capacity of the proteose-peptones to stabilize a model oil-in-water emulsion. Moreover, at all the concentrations examined, the purified component 3 showed a higher emulsifying activity than the total unpurified fraction.     

ANALYSIS OF EXPERIMENTAL AND NUMERICAL RESULTS OF A TURBULENT SWIRLING FLOW IN A TUBE

In many applications swirling flow is used to enhance heat and mass transfer. One of the problems of modelling a turbulent swirling flow is the choice of the turbulent closure model which is acceptable for engineering purposes. To evaluate which model performs best, numerical results are compared with experimental data. Local velocity measurements are carried out on a swirling flow in a circular tube. The measurement method is hot-wire anemometry combined with visualization techniques. The numerical analysis is carried out using the k-ε model and the Algebraic Stress Model. In the experiment a symmetrical swirl was observed, Comparing the experimental data with the numerical results shows that the Algebraic Stress Model represents the experimental data quite well, whereas the k-ε model fails.     

利用Visual C＋＋和Direct3D设计雷达显示器

利用Visual C＋＋和Direct3D对某雷达显示器的实现过程作了详细论述,包括数据采集、PPI型显示器、A型显示器、B型显示器、余晖显示、航迹显示等。通过试验证明,采用Direct3D绘图方式比采用GDI绘图方式效果好,更适用于数据处理量大、天线扫描速度快的雷达显示器。     

FTIR investigation of ethylene coordination and polymerization on reduced Cr/SiO2 catalyst

FTIR spectroscopy was applied to study the initial steps of ethylene polymerization on reduced chromia-silica (0.5 wt% Cr/SiO₂). To decrease the speed of the reaction small doses of gas were introduced to the catalyst in each run and C₂D₄ was used to confirm band assignments. At the initial steps of the reaction only ethylene molecules coordinated to probably Cr _A ²⁺ cations were observed. The concentration of such complexes was estimated to be about 50% of the total amount of Cr atoms in the sample. The FTIR spectrum of the polymer formed at the initial doses of C₂H₄ (when [C₂H₄] [Cr]) was found to be slightly different from that formed after excess ethylene was introduced onto the catalyst ([C₂H₄] > [Cr]).     

Characterization of ultrafine La x Sr1−x MnO3 powder prepared by spray pyrolysis

The characterization of La _x Sr_1−x MnO₃ powders produced by spray pyrolysis using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observation, specific surface area (Brunauer-Emett-Teller), and particle size distribution measurements shows that the resultant large particles are loose agglomerates consisting of many small particles. However, the sintered tiny particles can form hard agglomerates, and the particle size increases remarkably. The structures of the powders before and after sintering were identified by x-ray diffraction (XRD). The study of the electrical property of the powder shows that the powder is a metallic conductor. In a reducing atmosphere, the powder can be decomposed. When the powder is cofired with yttria-stabilized zirconia 5% (YSZ) powder at 1200 °C for 5 h, no new phase is produced, and the powder remains a single provskite hexagonal-rhombohedral structure.     

汽车覆盖件成形过程数值模拟研究

本文介绍汽车覆盖件成形过程有限元模拟两个软件ＩＴＡＳ—３Ｄ和ＤＹＮＡＭＩＣ的最新研究成果，基本原理和有关接触搜索、摩擦和拉伸筋模型等关键技术。并有两个应用实例     

AlF3贮仓料位计在线监控系统开发与应用

针对铝电解原材料中AlF3与Al2O3自动配料不准和难于观察及控制的现象，我厂开发应用了AlF3贮仓料位计，并与微机网络相连，实现了远程测量与在线监控，使AlF3配料更准确更均匀，电解质分子比更稳定，电解槽生产低耗高效。     

双波长分光光度法测定自来水中Fe2+和Fe3+的含量

采用双波长分光光度法测定 Fe2 和 Fe3 的方法 ,结果表明 ,在 λ1 =4 0 0 nm,λ2 =5 4 2 nm处 ,显色时间在 6 0 min～ 80 min,p H =4～ 5时能联合测定水中 Fe2 和 Fe3 ,其结果具有较高的精密度和准确度。     

Aplysia sea hare assimilation of secondary metabolites from brown seaweed,Stypopodium zonale

JuvenileAplysia dactylomela were found feeding in abundance on the tropical brown algaStypopodium zonale, a seaweed previously shown to contain numerous unique terpene-quinone natural products. Lipid extracts of these herbivorous mollusks were shown by TLC and HPLC-NMR analyses to contain appreciable quantities of twoS. zonale metabolites as well as one new but closely related compound. Spectroscopic analyses of the new compound in concert with functional group modifications identified this new compound as 3-keto epitaondiol. A careful analysis of the seaweed extract failed to locate this ketone, and thus, it most likely represents anAplysia-biotransformed compound. This is the first clear reported observation of metabolite transfer between an alga of the phylum Phaeophyta and a sea hare.     

熔块釉中三氧化二硼的测定

用NaOH熔融样品，向标准溶液中加入同样量的KOH基体，建立工作曲线，试样酸化后，直接用ICP－AES法测定。