In-tube condensation of mixture of R134a and ester oil: empirical correlations

This paper presents a comparative study of the condensation heat transfer coefficients in a smooth tube when operating with pure refrigerant R134a and its mixture with lubricant Castrol “icematic sw”. The lubricant is synthetic polyol ester based oil commonly used in lubricating the compressors. Two concentrations of R134a-oil mixtures of 2% and 5% oil (by mass) were analysed for a range of saturation temperatures of refrigerant R134a between 35 °C and 45 °C. The mass flow rate of the refrigerant and the mixtures was carefully maintained at 1 g/s, with a vapour quality varying between 1.0 and 0. The effects of vapour quality, flow rate, saturation temperature and temperature difference between saturation and tube wall on the heat transfer coefficient are investigated by analysing the experimental data. The experimental results were then compared with predictions from earlier models [Int J Heat Mass Transfer (1979), 185; 6th Int Heat Transfer Congress 3 (1974) 309; Int J Refrig 18 (1995) 524; Trans ASME 120 (1998) 193]. Finally two new empirical models were developed to predict the two-phase condensation heat transfer coefficient for pure refrigerant R134a and a mixture of refrigerant R134a with Castrol “icematic sw”.     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

液相颗粒包裹法制备PbNb2O6微粉的研究

本文介绍了一种采用液相颗粒包裹技术制备功能陶瓷微粉的新方法.这种方法有如下特点:(1)方法简便,不需要特殊的设备,便于扩大应用于工业生产;(2)粉体颗粒尺寸小而均匀;(3)粉体化学组成偏离小、且均匀;(4)适应性强,从双组分至十多组分的材料微粉制备均可采用;(5)特别适用于一些含有难溶组分、用液相法无法制备的材料.本工作采用这一方法,成功地制备出 PbNb_2O_6微粉,其平均腰粒尺寸<0.5μm,分散性及化学均匀性好,烧结活性高,烧结温度可以降低近100℃,瓷坯密度可达理论密度的96%以上.     

IPv6与欧洲

在推进IPv6的问题上,亚洲表现的最为积极,这是因为亚洲各国承受着巨大的IP地址方面的压力。欧洲虽然在这方面没有这样大的压力,但在互联网方面一直落后于美国,这是欧洲所不甘心的。因此,欧洲在推进IPv6方面也做了许多工作。欧洲推进IPv6的基本策略是先移动,后固定,并实施了一系列的行动计划和项目。欧洲面临的挑战主要是已经部署了数量巨大的网元、操作系统与软件应用必须予以更新、互通或取代,需要仔细规划和大量投资。     

气压传动与控制在电子专用设备上的应用

气压传动与控制已成为电子专用设备研制过程中一项不可缺少的内容 ,必须进行合理的气动系统设计及其控制 ,选择相应的气动元件以满足设备的功能要求。概述了气压传动与控制在电子专用设备上的应用。     

联产供冷与电力供冷能耗比较分析

文中将两种供冷能耗比较分解成用电煤耗差、用热煤耗量、增加产汽用电煤耗量三部分进行分析，按照热量法得出在目前一般情况下联产供冷比电力供冷通常费能和定性定量结论，为全面研究比较热电冷联产与分产的能耗奠定一个基础。     

遥操作工程机器人系统临场感技术研究-6自由度临场运动感觉反馈技术的研究进展

 研究开发出一种遥操作工程机器人系统，可以应用于诸如火灾现场的修复作业等广阔的领域．该系统由伺服控制的工程机器人、2根从远处操纵工程机器人的操纵杆、视频系统和6自由度运动模拟器组成．操作者坐于座椅上，座椅固定于运动模拟器的上方． 该系统需要解决的一个关键问题是如何使操纵者高质量地获得工作现场的临场运动感觉． 提出了一种6自由度临场运动感觉反馈方法，其信号源来自工程机器人上安装的6个加速度传感器． 该方法的有效性已为实验所证明，即应用6自由度运动模拟器不但可以高质量地模拟工程机器人单个自由度的运动：滚动、俯仰、转动以及前后、左右、上下的平移，而且可以高质量地模拟工程机器人的各种复合运动．     

移动IP综述

论述了移动IP的概念和发展过程，分析了国内外对移动IP研究的重点问题及其方法，对移动IP的发展方向进行了归纳和总结，并提出了有关用的问题。     

浅谈综合布线系统接地设计

综合布线系统作为建筑智能化不可缺少的基础设施,其接地系统的好坏将直接影响到综合布线系统的运行质量,故而显得尤为重要。本文介绍了综合布线系统接地的结构及设计要求,并提出在接地设计中应注意的几个问题。     

PDB-18C6对TI(Ⅰ),An(Ⅲ),Cu(Ⅱ)的吸附及从α轰击的金靶中分离~(199)TI

本文研究了用冠醚树脂二苯并-18-冠-6甲醛聚合物(简称PDB-18C6)对T1(Ⅰ),Au(Ⅲ),Cu(Ⅱ)的吸附行为。实验表明,在盐酸溶液中冠醚树脂的吸附效率顺序为Au(Ⅲ)>T1(Ⅰ)>Cu(Ⅱ)。用高氯酸和乙二醇乙醚淋洗T1(Ⅰ),Au(Ⅲ),它们的回收率一般在82-98.9％和98-100％。还在1.2m回旋加速器的外靶装置上,用25-27MeV的α粒子轰击金靶,累计束流强度为27μA·h,经处理分离后得到仅含0.50％~(200)T1的较高纯度的~(199)T1。