Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

Micromechanical approach to damage mechanics of composite materials with fabric tensors

The purpose of this study is to apply continuum damage mechanics – introduced through the concept of fabric tensors – to composite materials within the framework of the theory of elasticity. A directional data model of damage mechanics for composite materials will be developed using fabric tensors. The introduction of fabric tensors into the analysis of damage of composite materials will allow for an enhanced and better understood physical meaning of damage. The micromechanical approach will be used here to relate the damage effect through fabric tensors to the behavior of composite materials. In this approach, damage mechanics is introduced separately to the constituents of the composite material through different constituents’ damage effect tensors. The damaged properties of the composite system as a whole can then be obtained by proper homogenization of the damaged properties of the constituents.

The derivation of a generalized formulation of damage evolution will be shown here in a mathematically consistent manner that is based on sound thermodynamic principles. Numerical examples will be presented to show applicability. In addition, damage evolution for the one-dimensional tension case is also illustrated.     

Numerical analysis of two-dimensional steady-state and transient heat transfer in a parallel duct filled with pressurized He II

Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified.     

A new way for constructing high accuracy shock-capturing generalized compact difference schemes

The generalized compact (GC) schemes and some of their important properties are presented. And a new way for constructing high order accuracy and high-resolution GC schemes is presented. The schemes constructed by using this way could satisfy some principles and demands prescribed in advance to ensure some desired properties to the schemes, such as the principle about suppression of the oscillations, the principle of stability, the order of accuracy and number of scheme points, etc. As two examples, a three-point third-order compact scheme and a three-point fifth-order GC scheme satisfying the principle about suppression of the oscillations and the principle of stability are described in this paper. Numerical results show that these schemes are shock-capturing. The time-dependent boundary conditions proposed by Thompson are well employed when the algorithm is applied to the Euler equations of gas dynamics. Fourier analysis shows that the resolution characteristics are spectral-like.     

Microbiological safety of kinema, a fermented soya bean food

Kinema is a fermented soya bean food of Nepal and the hilly regions of North-eastern States of India. Generally, the fermentation is dominated by Bacillus spp. that often cause alkalinity and desirable stickiness in the product. The present study was undertaken in a limited number of commercial (market) kinema samples to test for the presence of foodborne pathogens and their properties. Bacillus cereus was present in numbers exceeding 10⁴ cfu/g product in five of the tested 15 market samples. Enterobacteriaceae and coliform bacteria exceeded 10⁵ cfu/g in 10 of the 15 samples. Escherichia coli exceeding 10⁵ cfu/g was found in two samples. Staphylococcus aureus was not detected in any of the tested samples. Of 31 isolated typical and atypical strains of B. cereus, 18 representative strains were tested qualitatively for the ability to produce diarrhoeal type enterotoxin (BCET) using an Oxoid BCET-RPLA test kit. Overall, BCET was formed by 12 strains in BHIG (brain heart infusion broth +1% glucose), by seven strains on sterilized cooked rice, and by five strains on sterilized cooked soya beans. Semi-quantitative tests on BCET revealed that levels exceeding 256 ng/g soya beans, produced by single pure culture inoculation with the isolated B. cereus strains, were reduced to ≤ 8 ng/g by frying kinema in oil, a common procedure when making kinema curry. It was also shown in a mixed pure culture experiment that a kinema strain B. Subtilis DK-W1, is able to suppress growth and BCET formation by a selected toxin producing strain (BC7-5) of B. cereus. It is concluded that the traditional way of making kinema and its culinary use in curries is safe. However, for novel applications of kinema, safety precautions are advisable.     

OSI参考模型与B—ISDN协议参考模型的比较

分析了ＯＳＩ参考模型和Ｂ－ＩＳＤＮ协议参考模型之间的关系，为Ｂ－ＩＳＤＮ与以ＯＳＩ为标准的数据网的互联打下了基础。     

Effect of cationic surfactant and inorganic anions on the electrochemical behavior of carbon steel in formation water

Corrosion behavior of carbon steel in formation water associated crude oil from Egyptian western desert was studied at various concentrations of dodecyl dimethyl ammonium chloride (CS) as a cationic surfactant. Polarization curves indicate that CS has a good inhibition efficiency for carbon steel in formation water and behaves as cathodic inhibitor. The inhibition efficiency was found to increase with increase in CS concentration until reaches a maximum constant value corresponding to the critical micelle concentration of CS and decrease with increase in solution temperature. The adsorption of CS follows the kinetic thermodynamic model and Flory-Huggins isotherm. Thermodynamic parameters obtained indicate that that the presence of the CS increases the activation energy. Polarization and Impedance measurements indicate that the addition of KI has a significant synergistic effect with CS and results in increase the inhibition efficiency of CS in formation water.     

Growth and optical property of zinc oxide thornballs

A new microstructure, thornball, of zinc oxide (ZnO) was synthesized by a very simple solid vapor deposition process under lead oxide (PbO) atmosphere. The microthornballs consist of numerous needles, which extend outwards in all directions symmetrically. They have dimensions of 120 μm in diameter, while the average diameter of the needles is about 100-200 nm. The needles on the balls grow along the 〈0 0 0 1〉 orientation and have gradient compositions along radial. Control experiments proved that PbO played an important role in the growth. Additionally, photoluminescence property was observed and provided the evidence that PbO did not deteriorate the optical properties of ZnO thornballs. This kind of microstructures has potential applications in the field of photochemical catalysis.     

Isothermal Gas Forming of Mg Alloy AZ31 Sheet

There have been reports on sheet forming of Mg alloy in industry via the punch and die method;this paper is probably the first formal one for studying the sheet formability of AZ31 employing pressurized gas to press the sheet into a female die cavity at various elevated temperatures.The results indicate it is feasible to form a rectangular box via pressurized gas from extruded sheets of 0.5 and 1.7 mm thick.The formed box has 1:2 depth over width ratio,which should be large enough when dealing with realistic industrial sheet forming parts.Presently,forming a sheet of 0.5 mm thick is considered a technical challenge by industry,and it is conquered as demonstrated in this paper.Gas forming technique applied to Mg alloy is unprecedented and shows potential for industrial utilization.     

Antimutagenic activity of natural phenolic compounds present in the common bean ( Phaseolus vulgaris ) against aflatoxin B 1

Polyphenols with antimutagenic and anticarcinogenic properties are present in fruits, vegetables and legumes. In this study, the Salmonella typhimurium tester strains TA98 and TA100 were used in the microsuspension assay to examine the antimutagenic effect of phenolic compounds extracted from the common bean (Phaseolus vulgaris) against mutagenicity induced by aflatoxin B 1 (AFB 1 ). A dose-response curve was constructed for AFB 1 ; from which a level of 40ng AFB 1 /tube was selected for all antimutagenicity assays. The AFB 1 and phenolic extract (PE) were not toxic to the bacteria at concentrations tested. In the case of PE, results were similar to the number of spontaneous revertants for TA98 and TA100. The inhibitory effect of PE against AFB 1 mutagenicity was dose-dependent at the lower concentrations tested (2.5, 5, 10, 12.5, 15 and 25 μg-equivalent ( + )-catechin/tube for TA98; 0.5, 1, 1.5, 2.5, 5, 10 and 25 μg-equivalent ( + )-catechin/ tube for TA100). Further, a two-stage incubation procedure was used to investigate the potential interaction between PE and AFB 1 . The greatest inhibitory effect of the PE on AFB 1 mutagenicity occurred when PE and AFB 1 were incubated together. When the bacteria were first incubated with PE followed by a second incubation with AFB 1 , lower inhibition was observed. Lower inhibition was also observed when the bacteria were first incubated with AFB 1 followed by a second incubation with PE. The results suggest that the mechanism of inhibition could involve the formation of a chemical complex between of PE and AFB 1 .