镁基储氢材料的研究进展

本文回顾和总结了近几十年来，特别是近十年来镁基储氢材料的发展情况，重点综述了机械合金化Mg-Ni2合金体系的研究情况及其近期的进展，从储氢材料成份及配比，制造工艺改进以及材料的组织结构对材料性能的影响等各方面进行一定的分析和归纳，对储氢材料研究中出现的问题以及今后的发展方向都作了探讨。     

Confinement-Shear Lattice Model for Concrete Damage in Tension and Compression: II. Computation and Validation

The concrete material model developed in the preceding Part I of this study is formulated numerically. The new model is then verified by comparisons with experimental data for compressive and tensile uniaxial tests, biaxial tests, and triaxial tests, as well as notched tests of mode I fracture and size effect.     

Preparation and Characterization of Energetic Nanocomposites of Organic Gel – Inorganic Oxidizers

Two types of polymeric sols, resorcinol‐formaldehyde (RF) and resorcinol‐furfural (RFur), were mixed in a water‐containing medium with aqueous solutions of inorganic salts: NH₄ClO₄, Mg(ClO₄)₂, and NH₄NO₃. After gelation and an ambient pressure drying, hybrid nanocomposites with properties of energetic materials were obtained. It was stated that salt concentration and addition of a second solvent (e.g., methanol or N,N‐dimethylformamide) to the mixture of reagents have crucial meaning for gel formation. In the case when only water was used, the mixture of organic sol/inorganic salt did not transfer from sol to gel, and precipitates were formed. Conventional drying of wet gelled composites leads to rigid material called xerogels. The RF xerogels are red and RFur xerogels are black. Typically, xerogels are transparent at low salt concentration (below 30%). The microstructure, morphology, and some other properties of chosen composites were studied by means of HR SEM, AFM, XRD, DTA/TG, and N₂ adsorption isotherm techniques. SEM observation revealed that sizes of the oxidizer particles vary from less than 100 nm to ca. 1000 nm. XRD analyses also confirmed the presence of nanometer‐sized crystals of oxidizers in some formulations. The specific surface area of polymeric matrix/oxidizer composites was found to be in the range from 0.002 to 0.3 m² g⁻¹. After removing the salt from the composites (by extraction with boiling water), the specific surface area grows even up to 210 m² g⁻¹. TG/DTA analyses showed that the tested composites decompose as typical energetic materials. If pre‐heated and exposed to flame, some of them (especially RF/Mg(ClO₄)₂ composites) undergo violent deflagration with loud sound and flash effect.     

Characterization of PAX‐21 Insensitive Munition Detonation Residues

Insensitive high explosives are being used in military munitions to counteract unintended detonations during storage and transportation. These formulations contain compounds such as 2,4‐dinitroanisole (DNAN) and 3‐nitro‐1,2,4‐triazol‐5‐one (NTO), which are less sensitive to shock and heat than conventional explosives. We conducted a series of four tests on snow‐covered ice utilizing 60‐mm mortar cartridges filled with 358 g of PAX‐21, a mixture of RDX, DNAN, and ammonium perchlorate. Rounds were detonated high‐ and low‐order using a fuze simulator to initiate detonation. Blow‐in‐place (BIP) operations were conducted on fuzed rounds using an external donor charge or a shaped‐charge initiator. Results indicate that 0.001 % of the original mass of RDX and DNAN were deposited during high‐order detonations, but up to 28 % of the perchlorate remained. For the donor block BIPs, 1 % of the RDX and DNAN remained. Residues masses for these operations were significantly higher than for conventional munitions. Low‐order detonations deposited 10–15 % of their original explosive filler in friable chunks up to 5.2 g in mass. Shaped‐charge BIPs scattered 15 % of the filler and produced chunks up to 15 g. Ammonium perchlorate residue masses were extremely high because of the presence of large AP crystals, up to 400 μm in the recovered particles.     

Temperature stable 0.35Ag2MoO4-0.65Ag0.5Bi0.5MoO4 microwave dielectric ceramics with ultra-low sintering temperatures

In this study, the novel temperature-stable (1-x)Ag₂MoO₄-xAg_0.5Bi_0.5MoO₄ microwave dielectric ceramics were prepared by a modified solid-state reaction method. The phase composition, microstructures and microwave dielectric properties of the (1-x)Ag₂MoO₄-xAg_0.5Bi_0.5MoO₄ ceramics were investigated. All the compounds can be sintered well at ultra-low temperatures (<540 °C). The XRD and SEM analysis indicate that the Ag₂MoO₄ and the Ag_0.5Bi_0.5MoO₄ can coexist with each other. When x = 0.65, the ceramics exhibit the best microwave dielectric properties with a relative permittivity of 23.9, a Q × f value of 16,200 GHz (at 7.3 GHz) and a near-zero TCF value of -2.4 ppm/°C at 520 °C. The results indicate that temperature-stable (1-x)Ag₂MoO₄-xAg_0.5Bi_0.5MoO₄ ceramics are promising candidates for low temperature co-fired ceramics (LTCC) applications.     

离子液体的应用进展

离子液体由于具有独特的物理化学性质而成为一种新型的绿色介质,近年来成为国际上研究的前沿和热点。它为开发新型绿色工艺,实现将传统重污染、高能耗工业过程的升级换代提供了新机遇。对离子液体应用的研究进展进行了综述,详细介绍了离子液体在催化科学、电化学、材料科学、环境科学和分离技术等领域的应用,并对其发展方向进行了展望。     

EPDM发泡材料应力松弛行为的数值模拟

利用两种发泡加工工艺,在相同EPDM橡胶基本配方基础上调节发泡剂用量,制备出四种密度不同的发泡材料.通过单轴压缩实验得到了EPDM发泡材料的应力松弛数据,采用理论推演建立的四单元变参数Maxwell模型,模拟EPDM发泡材料的应力松弛行为,拟合结果表明不同发泡程度的橡胶基材,其应力松弛时间和表观松弛强度略有差别,而气体...     

浅析国内外对于"仿瓷餐具"技术要求的差异

介绍了我国标准和欧盟、美国和日本食品接触材料法规对于密胺、脲醛模塑制品的技术要求,对其主要差异进行了对比分析.     

花生壳/PP复合材料的制备及其性能研究

为了实现对花生壳这一农产品的回收利用,采用花生壳粉末与PP制备应用于家居填充物的复合材料,对其最优工艺条件进行了研究,测试了所制备材料的拉伸、弯曲以及冲击特性.结果表明,随着花生壳粉末质量分数的增加,所制复合材料的拉伸、弯曲强度在花生壳粉末质量分数为40%时取得最大值,而冲击强度随着花生壳粉末质量分数的增加反而变小.所制备复合材料满足家居填充物要求的最优工艺为:当花生壳粉末质量分数为40%,热压温度175℃,热压压力12MPa,热压时间5min时.其弯曲性能、拉伸性能和冲击性能均较好.     

Modeling of pore structure evolution within the fiber bundle during chemical vapor infiltration process

Taking into account the gas diffusion parallel and perpendicular to the bundle axis, a two-dimensional model combining the non-conservative level set method and the steady-state diffusion equation is presented for evolving pore structure in the bundle cross-section. Parametric studies have been conducted to determine the sensitivity of residual porosity within the bundle to the structure parameters. Sheldon and Besmann's approach is revised and more realistic approximated expressions depicting the accessible and total porosity evolution inside the bundle are given. Such expression can serve as useful estimate of pore structure evolution for modeling the CVI process.