基于Hoek-Brown准则的深部岩体力学参数及其应用

基于Hoek-Brown经验强度准则,采用最小二乘法拟合出岩体力学强度参数,并与H-B_02ed推荐的等面积拟合结果进行对比,结果发现两种拟合方法得出的岩体内摩擦角数值相差很小,但等面积拟合法得出的黏聚力强度远高于最小二乘拟合法。将两种强度参数拟合结果应用于深部矿体开采的数值模拟,发现采用最小二乘拟合法的岩体强度参数其模拟结果更接近工程实际。该方法对深部岩体力学参数的确定具有一定的借鉴意义。     

水力旋流器内清水流场空气柱的三维数值模拟

本文依据计算流烙动力学（CFD）的计算方法,利用Fluent软件对带有空气柱的固-液分离用水力旋流器内清水流场进行了三维数值模拟研究。文章中首次采用“mixture”模型对空气柱进行模拟,模拟所得的流场与实测结果作对比,证明效果良好。本文的工作对进一步研究旋流器固-液分离现象提供了一定的基础和参考。     

微波着陆引导系统多径效应的数字仿真

为分析和评估多路径效应对MLS测角误差影响,提出了一种基于几何光学和射线寻迹理论的MLS多路径角度误差数字仿真新方法. 该方法依据几何光学和几何绕射理论在获得多径信号与直达信号电压比的基础上,通过射线寻迹计算多径直达信号相位差,而后对叠加包络的角度误差方向图分解为波束内和波束外多路径误差进行研究,实现角度误差数字仿真. 利用该方法对某机场典型环境的多路径问题进行了数字仿真,并将仿真结果与经典模型进行了对比,验证了其可行性.     

底部局部辐射加热窑炉内温度场数值模拟

提出了底部局部辐射加窑炉内温度场数值分析的控制方程组，分别对平面加热及半圆柱形加热面两种算例进行了数值计算，得了影响烤花烤窑炉内温度场均匀性的主要因素和有加热面发射率，加热面形状，加热面相对位置及窑炉墙体热阻和墙体与外界的换热热阻。     

Studies of surface and gas reactions in a catalytically stabilized combustor

A numerical investigation of a catalytically stabilized thermal (CST) combustor was conducted for a multichannel catalyst bed, and both the catalyst bed and thermal combustor were simultaneously modeled. The numerical model handled the coupling of the surface and gas reaction in the catalyst bed as well as the gas reaction in the thermal combustor. The behavior of the catalyst bed was investigated at a variety of operating conditions, and location of the flame in the CST combustor was investigated via an analysis of the distribution of CO concentration. Through parametric analyses of the flame position, it was possible to derive a criterion to determine whether the flame is present in the catalyst bed or the thermal combustor for a given inlet condition. The results showed that the maximum inlet temperature at which the flame is located in the thermal combustor increased with increasing inlet velocity.     

不同工况下仿生叶轮水上推进性能数值分析

研究采用蛇怪蜥甥踏水机理设计的轮-叶复合式仿生推进装置,针对实现推进性能最大化的仿生叶轮装置设计的难点,从减少叶片能量损失的角度设计了一种压水防溅型仿生叶轮结构,如何有效获取新型叶轮结构的水上推进性能,应用计算流体力学数值方法,通过构建不可压缩非稳态的N-S主控制方程,采用欧拉网格有限体积法的离散化处理方式,综合应用VOF模型和动网格技术,实现对新型仿生叶轮水上推进性能的数值模拟,着重讨论了不同转速ω和负载P下的仿生叶轮水平速度v1和水平位移s1的变化规律,研究仿生叶轮运动中压力场、速度场和气液相的分布特点,获得了转速ω和负载P对仿生叶轮水上推进性能的影响规律.仿真分析结果表明转速ω和负载P均存在一合理区间范围,使得新型仿生叶轮推进性能最优,仿真结果可为实现仿生叶轮模型水上推进性能最优提供了理论基础.     

运载火箭六自由度仿真平台搭建与应用

研究运载火箭六自由度仿真系统设计问题,在传统火箭六自由度仿真平台设计中常以特定任务为导向,造成仿真系统碎片化严重,扩展重用性不足.同时,数值仿真与视景仿真的交互中存在实时驱动的问题.针对上述问题,采用面向对象的模块化设计方法,建立了运载火箭六自由度仿真模型,给出了三层结构的通用仿真框架.设计了仿真消息管理器,较好地解决了数值仿真与视景仿真的集成并保证了系统的实时性.仿真结果验证了模型建立的准确性以及仿真平台的可靠性和稳定性.仿真结果对于运载火箭设计和性能评估系统的建立有着良好的借鉴意义.     

浅谈解的存在唯一性定理在《偏微分方程数值解》中的应用

从一个新的角度讨论常微分方程中解的存在唯一性定理在偏微分方程数值解法中的重要应用。给出一类伪双曲型偏微分方程的新的分裂混合有限元数值格式,将该格式转化成常微分方程系统,利用解的存在唯一性定理证明该系统是存在唯一解的。通过简短的讨论、概述明确解的存在唯一定理在偏微分方程数值解中的应用方法．并希望能够在教学科研未来的发展中有新的观念。     

Identification methods for anomalous stress region in coal roadways based on microseismic information and numerical simulation

It is believed that the microseismicity induced by mining effect and gas gradient disturbance stress is a precursor to the essential characteristics of roadway unstability. In order to effectively identify and evaluate the stability of coal roadways in the process of mine development and extraction, a microseismic monitoring system was deployed for the study of the stress evolution process, damage degree and distribution characteristics in the tailgate and headgate. The mine under study is the 62113 outburst working face of Xin Zhuangzi coalmine in Huainan mining area. The whole process of microfractures initiation,extension, interaction and coalescence mechanisms during the progressive failure processes of the coal rock within the delineated and typical event clusters were investigated by means of a two dimensional realistic failure process analysis code(RFPA2D-Flow). The results show that the microseismic events gradually create different-sized event clusters. The microseismicity of the tailgate is significantly higher than that of the headgate. The study indicates that the greater anomalous stress region matches the area where microfractures continuously develop and finally connect to each other and form a fissure zone.Due to the mine layout and stress concentration, the ruptured area is mainly located on the left shoulder of the tailgate roof. The potential anomalous stress region of the coal roadway obtained by numerical simulation is relatively in good agreement with the trend of spatial macro evolution of coal rock microfractures captured by the microseismic monitoring system. The research results can provide important basis for understanding instability failure mechanism of deep roadway and microseismic activity law in complex geologic conditions, and it ultimately can be used to guide the selection and optimization of reinforcement and protection scheme.     

Gateside packwall design in solid backfill mining-A case study

Based upon characteristic movement features of the overlying strata in solid backfill mining and in-situ observations,an associated model representing a roadway support system has been developed.Based on the Winkler foundation and beam model,the current study presents a static analysis of the model,thus permitting acquisition of a theoretical formula pertaining to roof convergence.Through use of working face 6304-1(Jisan Colliery) as the research setting,the association between roof convergence magnitude and both packwall strength and width have been elucidated.Based upon observed conditions at the working face,realistic packwall parameters have been formulated,with numerical simulation results and field application results indicating that design parameters garnered from the developed formula successfully adapted to local geological movement and deformation.Accordingly,roadway deformation was shown to be within the permissible range,thus satisfying mine production requirements.The proposed method in the current study may give a design basis for pack design in the context of SBM under similar conditions.