石英砂的相变与换向器套筒铸件的变形

用呋喃树脂石英砂工艺生产牵引电机换向器套筒出现变形、裂纹等铸造缺陷,是由石英砂相变膨胀引起,后用高铬刚玉砂代替石英砂得到解决.     

实现铝锭堆垛、称量、打包一体化控制系统

国内大多数铝锭生产企业在铝锭打包过程中。均采用人工作业方式。为此，根据铝锭生产工艺和技术要求以及现代科学生产管理理念。探讨铝锭称量、堆垛、打包一体化控制系统的研究，其主导思想是在原有的铝锭堆垛机控制系统上，实现铝锭自动化流水作业的功能，改变原有的铝锭生产作业方式。     

On certain aspects of strain rate sensitivity of sheet metals

The formability of a material depends upon the strain hardening and strain rate hardening of the material. In this study, constitutive parameters using the power law constitutive equation are determined for six different strength steels and two aluminum alloys over different strain ranges, including approximations of the postuniform elongation range. Constitutive parameters are found to be different at different strain ranges. The strain hardening of steels increases with strain at low strain levels (less than 5%) and decreases at high strain levels (greater than 10%). Strain rate hardening decreases with strain for all steels and aluminum alloys. Uniform elongation depends only on strain hardening, and postuniform elongation depends only on strain rate hardening. However, the total elongation depends on both strain hardening and strain rate hardening.     

热处理对多孔铝合金压缩吸能性能的影响

采用渗流铸造工艺 ,制备了Al Si系多孔铝合金 ,讨论了其压缩变形特征及能量吸收性能 ,分别对ZL10 1、ZL111两种多孔铝合金进行T6热处理 ,研究了热处理对这两种多孔铝合金压缩吸能性能的影响。研究结果表明 ,热处理能够提高多孔铝合金的能量吸收能力 ,对屈服强度及能量吸收效率也有显著的影响 ,为提高多孔铝合金的压缩性能 ,应尽可能施行热处理     

Effect of equal channel angular extrusion on the microstructure and superplasticity of an Al-Li alloy

This research investigates the use of equal channel angular extrusion (ECAE) processing to produce a superplastic form of the aluminum alloy 2098. The starting material was a hot-rolled and precipitation-hardened plate with elongated grains of width 67–92 μm, and a composition in weight percent of 2.2% Li, 1.3% Cu, 0.73% Mg, 0.05% Zr, balance Al. Microstructural evolution was investigated with optical and transmission electron microscopy (TEM) and microhardness measurements after each step of a multipass ECAE process. ECAE produced a submicron grain structure with an average size of about 0.5 μm. The sub-grain microstructure size was a function of the magnitude of the input strain and the extrusion temperature. Misorientation angles of the developed submicron structure increase with increasing number of passes at warm working temperatures. Superplastic behavior of the ECAE-processed alloy was achieved. However, the low zirconium content of the 2098 alloy resulted in grain growth of the refined structure at the superplastic processing temperatures, placing a lower limit on the deformation rates that can be used.     

宽幅高速铝箔轧机轧制铝箔面残留油的原因及其预防

介绍了宽幅高速铝箔轧机轧制铝箔过程中，箔面残留油对产品质量的影响，探讨了箔面发生残留油的原因及其改进措施。     

铝合金激光-电弧复合焊接工艺研究

对LF6铝合金的激光-电弧复合焊接工艺进行了初步研究。通过工艺试验,分析研究了焊接速度、激光焦点位置、钨极与激光束之间的距离、焊接电流对焊缝质量(熔深、熔宽)的影响规律。     

Effect of pulse parameters on microstructure of joint in laser beam welding for SiC_p/6063 composite

1　INTRODUCTIONSiC particlesreinforcedcomposites ,thankstotheirlowcostsandhighlevelofstructuralproperties ,areshowingtheirpotentialincivilandmilitaryappli cation .SiC particlesreinforcedaluminummatrixcomposites wideapplicationinaerospaceandautomo tiveareattributedtotheirperformanceofhighspecif icstrength ,highspecificstiffness ,highelasticmodu lusandexcellentwearresistance .Thecoefficientofthermalexpansionandthermalconductivitycanberegulatedbychangingthecontentandsizeofrein forcingparticl…     

智能温度控制仪在铝电解铸造保温炉上的应用

简要介绍了KX-C智能温控仪的性能、特点;结合铝电解铸造保温炉的控制要求,阐述了KX-C智能温控仪对保温炉的恒温控制过程。应用表明,该仪器由于具有控制准确、动作灵敏、接线简单、无需校准、成本较低、可靠性高、无需维护等优点,可很好满足实际生产的要求。     

N、S共掺杂碳基高效氧还原催化剂的制备

杂原子掺杂碳基氧还原（ORR）催化剂具有代替Pt基催化剂的巨大潜力。以硫掺杂g-C₃N₄（S-doped g-C₃N₄, S-g-C₃N₄）作为硫源和氮源,以三嵌段共聚物P123作为碳源,通过简单的高温热解法成功制备了N、S共掺杂碳（N, S co-doped carbon, NSC）催化剂,并考察了热解温度对制备的NSC催化剂ORR性能的影响。材料表征结果显示:温度为1 000 ℃时制备的催化剂NSC-1000具有较高的氮含量和硫含量及最大的比表面积;电化学测试结果显示:NSC-1000具有最佳的ORR性能,在0.1 mol/L KOH溶液中半波电位（half-wave potential, E1/2）高达0.888 V,且经10 000圈循环伏安扫描后E1/2仅负移12 mV,表现出极佳的活性和稳定性。此外,旋转环盘电极测试结果显示:NSC-1000催化剂主要以四电子反应路径催化ORR的发生。本实验为制备N、S共掺杂碳基高效ORR催化剂提供了新的思路。