SO4^2-／ZrO2固体超强酸的制备及其催化合成ETBE的研究

采用沉淀一浸渍法制备了负载型SO4^2-／ZrO2固体超强酸催化剂，运用IR、XRD等方法表征所制备催化剂的物化性质。结果表明，所制备的催化剂具有固体超强酸催化剂的特征，酸性与焙烧温度有关，适当提高焙烧温度有利于样品酸强度的提高，但焙烧温度过高会导致脱硫；浸渍液H2SO4浓度高有利于提高催化剂的硫含量，但是浓度过高，会在催化剂上形成硫酸盐，从而降低催化剂的比表面积和酸性。采用制备的催化剂气相催化乙醇与叔丁醇合成乙基叔丁基醚反应，乙基叔丁基醚的选择性为54．71％。     

2.5GHz低相位噪声CMOS LC VCO的设计

用0 .35μm、一层多晶、四层金属、3.3V的标准全数字CMOS工艺设计了一个全集成的2 .5 GHz L C VCO,电路采用全差分互补负跨导结构以降低电路功耗和减少器件1/ f噪声的影响.为了减少高频噪声的影响,采用了在片L C滤波技术.可变电容采用增强型MOS可变电容,取得了2 3%的频率调节范围.采用单个16边形的对称片上螺旋电感,并在电感下加接地屏蔽层,从而减少芯片面积,优化Q值.取得了在离中心频率1MHz处- 118d Bc/ Hz的相位噪声性能.电源电压为3.3V时的功耗为4 m A.     

P(DBF-VA)型柴油低温流动性改进剂的研制

针对新疆地产柴油蜡含量较高的特点,以游离基聚合法合成了富马酸双链混合酯和醋酸乙烯酯共聚物型[P(DBF-VA)]柴油低温流动改进剂,利用正交实验研究了单体配比,引发剂用量,溶剂用量,聚合温度对聚合物降冷滤效果的影响。共聚物用IR进行表征,利用XRD初步探讨了该降凝剂的降凝机理。结果表明:该剂能使吐哈—10~#、0~#柴油冷滤点降低10℃和7℃;使独山子0~#柴油冷滤点下降12℃;使石化0~#柴油冷滤点下降8℃;使克拉玛依0~#柴油的冷滤点下降8℃。     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

诱导水解法制备微细高分散金红石型二氧化钛

采用加热TiCl4稀溶液的方式,制备晶种,将其导入一定浓度的TiCl4溶液中进行诱导水解。所得的偏钛酸经干燥、煅烧后得到分散性好,D50为1 mm以下,金红石含量为≥95%的高纯TiO2,可用于生产PTC热敏电阻等铁电陶瓷。     

Nd3+:Y0.5Gd0.5VO4晶体生长和基本特性

Nd^3 :Y0.5Gd0.5VO4晶体作为一种新的激光材料，可以用中频感应加热提拉法生长。X射线粉末衍射分析表明它的结构与Nd^3 :YVO4晶体结构相同，它的晶格常数介于YVO4和NdVO4晶格常数之间。用ICP光谱法测定晶体中Nd^3 含量为0．8at％，分凝系数为0．8，与Nd^3 :GdVO4晶体中Nd^3 的分凝系数0．78相当；用称重法测定其密度为5．00g／cm^3；用稳态纵向热流法测出其室温热导率为12．5W／mK。实验表明Nd^3 :Y0.5Gd0.5VO4晶体有希望作为高功率ID泵浦激光晶体材料。     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

硅胶固载光敏剂的合成及其在反式维生素D3光敏异构化为顺式维生素D3中的应用

采用丙二酸作为连接,针9－蒽甲醇连接到硅胶上生成硅胶固载的光敏剂。利用此因相光敏剂分别在乙醇和甲苯溶液中敏化反式维生素D3。实验结果表明，此固相光敏剂能够有效地敏化反式维生素D3为顺式维生素D3的反应，并且非常容易从反应体系中分离出来。     

Niobium-containing catalysts—the state of the art

This review article is devoted to the materials containing niobium, which have been discovered or developed in the past few years and exhibit the potential application in heterogeneous catalysis. Niobium oxides and mixed oxides as well as sulfides, nitrides (oxynitrides), carbides (oxycarbides), and phosphates are considered. Among the catalytic processes in which Nb-containing materials were tested, liquid and gas phase oxidation is described in details, and the role of niobium in the prevention of the catalyst from SO₂ poisoning is mentioned.     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry