预处理对热电池阳极材料LiB合金结构和性能的影响

在LiB合金材料的制备中加入冷挤压和热处理两步预处理工艺;采用X射线衍射仪、扫描电镜测试合金的物相组成和微观组织;研究了预处理工艺对材料的密度、硬度、力学性能、热稳定性和放电性能的影响。结果表明:相对直接轧制方法制备的LiB合金材料,采用预处理工艺,提高了合金材料中Li7B6的相对含量,同时使合金结构和成分更均匀、致密,从而提高了合金的密度、硬度,合金的抗拉强度和断裂延伸率也显著提高;预处理使材料骨架孔洞缩小而且分布均匀,因此也促进了材料热稳定性的提高;材料的放电性能显著提高,放电容量由5 244提高至6 552 C/g。此外,与直接轧制工艺相比,采用冷挤压和热处理两道预处理工艺减少了多孔的合金锭与可反应气氛接触的时间,防止了氧化作用,消除了开裂、麻点等缺陷,大大提高了材料的加工成材率,使其成材率由不到50%提高至70%以上。     

板料激光成形技术

综述了激光成形技术的国内外发展史及其研究现状,分析了激光弯曲成形技术的优点,探讨了激光弯曲成形技术的原理及成形机理,并且论述了激光弯曲成形的影响因素,展望了板料激光成形技术的应用前景。     

Thermodynamic study of the phase equilibria in the Sn−Ti−Zn ternary system

The Sn−Ti−Zn ternary phase diagram has been constructed using the CALPHAD technique. The Ti−Zn binary system phase boundaries were determined using differential scanning calorimetry and the solid-liquid diffusion couples method. In addition, the formation energy of some stoichiometric compounds was obtained using first-principle band energy calculations. For the ternary system, some alloys were prepared by equilibration at 600 or 700 °C, and the compositions of the precipitates were analyzed using electron probe microanalysis. Thermodynamic assessment of the Ti−Zn and Sn−Ti−Zn systems was performed based on the experimental information and by adopting reported values of the thermodynamic properties of the Sn−Zn and Sn−Ti binary systems. Microstructural observation showed that Sn₃Ti₅Zn₁₂ exists in the ternary system. Seven types of invariant reaction on the Sn-rich liquidus surface of the ternary system are predicted by the phase diagram calculations. The ternary eutectic point falls at 0,0009 mass% Ti and 8.69 mass% Zn, at T=192.40°C, which is slightly lower than the calculated eutectic point of Sn−Zn binary alloy (T=192.41°C). Based on these results, a nonequilibrium solidification process using the Scheil model was simulated. This paper was presented at the International Symposium on User Aspects of Phase Diagrams, Materials Solutions Conference and Exposition, Columbus, Ohio, 18–20 October, 2004.     

铜基形状记忆合金马氏体相变宏观形状应变特征

利用X射线衍射仪、透射电镜、扫描电镜、原子力显微镜等研究了Cu-18Al-9Mn-3.4Zn(摩尔分数,%)形状记忆合金的马氏体晶体结构、亚结构以及马氏体相变宏观形状应变特征.结果表明:该合金的马氏体晶体结构为18R结构,亚结构为层错;单变体马氏体表面浮凸呈"( ) "型,浮凸高度为400～500nm,浮凸宽度为2 000～2 400 nm;多变体马氏体表面浮凸呈"N"型和"山尖"型,浮凸高度为200～400 nm,浮凸宽度为1 000～1 800nm;浮凸角均为8°～12°;马氏体相变符合G-T模型的双切变特征,惯习面为(113)面.     

Sn-Ag-Cu表面贴装元件的水清洗技术

采用SMT450-LD全自动SMT水清洗系统对模拟试件和贴装有片式电阻的PCB板表面残留物采用水基清洗剂清洗。结果表明，用Sn—Ag-Cu免清洗焊膏贴装在FR4基板上的片式电阻，焊后采用水基清洗剂清洗，表面残留物离子浓度为1．9μg/cm^2，达到美国军用标准MIL—STD-2000小于5．7μg／cm^2的规定。清洗过程中参数的设置，如清洗温度，清洗时间会对清洗效果产生较大影响。     

辊底式热处理炉的改造

原江西新钢钢管有限责任公司的2座辊底式热处理炉,由于是采用人工手动调节煤气流量来控制温度,由此导致钢管热处理质量不稳定,加之冷料入炉,加热时间长、出炉烟气温度高,需进行改造。通过对炉型结构、燃烧系统及炉温控制系统3个方面的改造,达到了提高炉子产量、产品质量及节能降耗的效果。     

表面微观屈服强度与疲劳极限的关系SCIEI

本文利用X射线对不同碳含量钢的表面微观屈服强度进行了研究。试验结果表明,表面微观屈服强度σ_(ms)远低于整体材料的屈服限,是一个反映表面抵抗塑性变形能力大小的参量。材料光滑疲劳极限往往是由裂纹荫生所控制的,与表面抵抗塑性变形的能力有关。本试验表明不同材料的σ_(ms)与存活率为50％疲劳极限的关系为:σ_(ms)=(0.81—1.02)σ_(-1);40Cr不同热处理状态的σ_(ms)与存活率为99.9％疲劳极限的关系为:σ_(ms)=(0.98—1.10)σ_(-1)。σ_(ms)的测定要比疲劳极限σ_(-1)的测定省时得多,有可能在工程上获得应用。     

高锰钢的泡沫陶瓷过滤净化

采用泡沫陶瓷过滤片对高锰钢进行过滤处理，对其进行金相分析和测试密度，冲击韧性和耐磨性能，并与未过滤的高锰钢进行对比，实验结果表明，在过滤的高锰钢中，金属夹杂物明显减小，密度提高0．53％，冲击韧性39．5％，耐磨性能提高1．04倍，批量生产结果表明，过滤的高锰钢球磨机衬板的使用寿命提高0．6－0．7倍。     

Kinetics of hydrogen absorption and desorption of magnesium nickel alloy

Reaction rates in the Mg₂Ni---H₂ system are still unclear, although they are needed for the process/optimization of hydrogen storage reactors. In this article, the rates of hydrogen absorption and desorption of the magnesium nickel alloy were investigated at different pressures up to 2.0 MPa using a constant-temperature thermogravimetric method. The powder of the alloy was microencapsulated with copper to improve the alloy properties (such as cycling strength) as a pretreatment. In the experiments, weight changes of the smallest amount possible of samples were monitored with the help of an ultra-accurate thermobalance, in order to avoid changes of the sample temperature due to the heat of the reaction. The reaction curves obtained revealed unique dependence of temperature and pressure and influence of thermal hysterisis. It is also possible that hydrogen-absorption and-desorption rates of this hydrogen storage alloy are expressed by the rate equation of first-order reversible reaction.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。