液化天然气供气站的工艺设计

〗LNG供气站的设计核心是工艺设计，设计中应注意以下几点：正确处理技术先进性与经济合理性的关系，综合权衡设置费与运营费的比例，力求项目全寿命费用最低；大多数城市LNG供气站均利用空气气化LNG，单罐容积为100 m³的真空压力式储罐广泛用于储存量为1200 m³以下的LNG供气站；为正确设置储罐安全阀的开启压力和排放压力，必须根据储罐的最高工作压力按照规范正确确定储罐的设计压力；储罐上2套独立的液位计和高、低限报警自动切断装置可确保储罐安全运行；空温式气化器的气化能力按用气城市高峰小时计算流量的1.3~1.5倍确定，为便于自然化霜应设置2套空温式气化器切换使用；空温式气化器出口串接水浴式加热器可提高冬季或雨天出口天然气温度，保护碳钢管道并降低供销差；LNG储罐区应设置围堰，消防用水量为喷淋与水枪用水量之和。最后建议，必须尽快颁布国家LNG设计规范，以提高我国的LNG设计水平。     

我国风机盘管技术现状分析

介绍了近年来我国在风机盘管技术领域的最新成果，在结构形式、强化传热、提高室内空气品质、降低噪音和提高自动控制水平等方面的技术进展情况，分析了目前风机盘管中存在的问题，并对今后的发展方向进行了展望。     

微型生化分析仪样品室温度控制系统研究

结合微型生化分析仪样品室的要求,设计了一种基于单片机的微型生化分析仪样品室温度控制系统.它以AT89S51为核心,采用单总线高精度数字温度传感器DS18B20对样品室温度采样,同时利用汇编语言编写温度设定与控制程序,采用半导体制冷的方式,实现了温度在25℃、30℃、32℃和37℃四个温度值的稳定,控制精度达±0.5℃.     

富氧燃烧技术在梭式窑中的应用

研究了富氧燃烧技术对梭式窑烧成的影响.研究结果表明,随着氧浓度从21%-30%的逐渐增加,CO总浓度和NO总浓度都先明显下降,后缓慢上升;节能效果在初始段较为明显,而后效果不明显;而实际烟气量与氧浓度成反比,与过剩空气系数成正比.     

HAT-095催化剂运行末期的优化探索

通过优化工艺条件,严控进料质量、改造循环氢压缩机油系统、调整二甲苯塔操作等措施,使催化剂在运行末期,也能发挥出良好的催化性能,并延长催化剂使用寿命;提高了催化剂处理C10芳烃的能力,降低重芳烃产率,提高经济效益。为催化剂运行末期操作和正常操作提供有益的探索。     

风管摩擦阻力的直接计算方法

提出用高精度的反映密度、黏度和温度关系的经验公式和Colebrook公式计算风管摩擦阻力系数的方法。分析和算例表明，用该方法计算，计算结果比采用常用工程设计方法更为准确，为应用计算机进行风道设计提供了直接、简便的方法。     

Drying Kinetics of a Porous Spherical Particle and the Inversion Temperature

A model is presented for drying of a single porous particle with superheated steam and humid air. Experimental data for spherical porous ceramic particle reported in the literature were used for the validation of the model. An inversion temperature at which the evaporation rates within superheated steam and humid air are equal was predicted. The effect of thermophysical properties of the particle (permeability 10^-14 - 10^-17 m², diameter 3 × 10^-3 - 10 × 10^-3 m) and operating variables (gas mass flux 0.26 - 0.78 kg m^-2 s^-1, drying agent temperature 120-200°C) is tested. The inversion temperature is shown to be affected by the thermophysical properties of the porous particle and of the drying agent.     

青藏铁路西格二线混凝土冻融试验研究

由于工期的要求,青藏铁路西格增建二线必须进行冬期施工。根据工程状况,分析了混凝土受冻的破坏机理,针对施工环境及对混凝土设计强度和要求,进行了大量冻融试验分析,对引气剂、水胶比、砂率、粉煤灰掺量等原材料与混凝土含气量的关系及其混凝土搅拌温度与静停时间等对混凝土性能的影响进行了分析与技术论证,确保了该线冬期混凝土施工顺利进行。     

气浮设备的应用与比较

结合气浮设备的工作原理，从使用效果这一角度介绍了几种气浮设备的应用情况。对新型高效浅池气浮设备的“零速原理”及国内外同类设备对比、应用情况作了简单的介绍。     

Performance evaluation of a water/silicone oil two‐phase partitioning bioreactor using Rhodococcus erythropolis T902.1 to remove volatile organic compounds from gaseous effluents

BACKGROUND: In the framework of biological processes used for waste gas treatment, the impact of the inoculum size on the start‐up performance needs to be better evaluated. Moreover, only a few studies have investigated the behaviour of elimination capacity and biomass viability in a two‐phase partitioning bioreactor (TPPB) used for waste gas treatment. Lastly, the impact of ethanol as a co‐substrate remains misunderstood. RESULTS: Firstly, no benefit of inoculation with a high cellular density (>1.5 g L^?1) was observed in terms of start‐up performance. Secondly, the TPPB was monitored for 38 days to characterise its behaviour under several operational conditions. The removal efficiency remained above 63% for an inlet concentration of 7 g isopropylbenzene (IPB) m^?3 and at some time points reached 92% during an intermittent loading phase (10 h day^?1), corresponding to a mean elimination capacity of 4 × 10^?3 g L^?1 min^?1 (240 g m^?3 h^?1) for a mean IPB inlet load of 6.19 × 10^?3 g L^?1 min^?1 (390 g m^?3 h^?1). Under continuous IPB loading, the performance of the TPPB declined, but the period of biomass acclimatisation to this operational condition was shorter than 5 days. The biomass grew to approximately 10 g L^?1 but the cellular viability changed greatly during the experiment, suggesting an endorespiration phenomenon in the bioreactor. It was also shown that simultaneous degradation of IPB and ethanol occurred, suggesting that ethanol improves the biodegradation process without causing oxygen depletion. CONCLUSION: A water/silicone oil TPPB with ethanol as co‐substrate allowed the removal of a high inlet load of IPB during an experiment lasting 38 days. Copyright © 2008 Society of Chemical Industry