A disposable single-use electrochemical sensor for the detection of uric acid in human whole blood

We report here a non-enzymatic detecting electrode strip for fast monitoring of uric acid in human whole blood. A single-use amperometric uric acid sensor strip, incorporating a three-electrode configuration, has been fabricated on a polypropylene substrate using low cost screen-printing (thick-film) technology. Both the working and counter electrodes were prepared by screen-printing commercial carbon ink. The integration on the same support of pseudo-reference electrode was obtained by screen-printing a commercial silver ink and subsequent electrochemical pretreatment. Simply by placing a 20 μl human whole blood drop on the strip is enough for uric acid analysis by square-wave voltammetry. Real human whole blood samples were analyzed by this method and compared to the phosphotungstic acid clinical test procedure with satisfactory results.     

中原油田气井堵水工艺技术探讨

针对中原油田气田的开发现状,为寻求更加经济、有效的治水措施,通过对国内外气田开发状况的调研,对找水技术和堵水技术进行了归纳,在此基础上研究出适合于中原油田气井堵水的GWPA堵剂系列,现场应用效果较好。     

广播电视发射台技术指标集中自动测试系统

本文介绍了利用计算机技术、网络技术、三遥技术对广播电视发射技术指标进行实时自动测试的系统，以便进一步为安全优质播出提供技术保证。     

高应力水平下滚动轴承疲劳寿命试验研究

通过在三种不同的强化负荷下进行深沟球轴承疲劳寿命试验，并与常规试验一组结果对比。结果表明，适当地加大滚动轴承疲劳寿命试验负荷，可以大大缩短试验时间，而疲劳寿命依然服从Ｗｅｉｂｕｌ分布，且与常规试验结果基本一致，同时疲劳破坏的形式仍是表面下萌生裂纹，然后扩展至表面形成剥落。     

铸造高性能合金的显微组织及耐腐蚀行为

对铸造高性能合金Lewmet55进行了化学成分设计，确定了该合金中镍、铬、钼、铜和硅的含量。采用金相显微镜和X射线衍射相结合的方法，分析了该合金的显微组织，并采用多种腐蚀试验方法研究其耐腐蚀行为。着重研究了不同热处理制度对铸造高性能合金的均匀腐蚀、晶问腐蚀、点蚀和电化学腐蚀性能的影响。试验结果表明，Lewment55合金经1250℃×1．5h水冷固溶处理后，在高温浓硫酸介质中具有良好的耐蚀性，以及较好的抗晶间腐蚀、点蚀和电化学腐蚀性能。     

正交试验法于优选白瓷坯料配方中的应用

对长石、石英、龙岩土、莱阳土４种因素各取４个水平，用正交表Ｌ１６（４５）安排１６个试验，分析了这１６个试验产品的吸水率、白度、热稳定性与每种因素各水平之间的关系．得出了白瓷坯料的最佳配方。其中，长石１９，石英２１，龙岩土２１．莱阳土０．     

50kg／m钢轨轨底缺陷的检验和分析

钢轨轨底缺陷有三种：底伤、结疤和底裂缺陷。取２０根有底缺陷５０ｋｇ／ｍＵ７１Ｍｎ钢轨做试样，通过低倍、断口、金相检验和扫描电能谱分析，详细描述了轨底缺陷的宏观和微观特征，研究出钢轨轨底缺陷出现的规律臁其产生的原因。通过对比试验，发现淄博１号保护渣有利于改善钢锭表面质量，提高钢轨一级品率。     

Monitoring Power Dissipation for Fault Detection

In this paper, we suggest that the dynamic power dissipation of acircuit can be used for fault detection. Even those faults which do notaffect static power dissipation can be detected by monitoring dynamic powerdissipation. We discuss how stuck-at, stuck-open, and redundant faults maybe detected by monitoring dynamic power dissipation. In many cases, theFourier spectra of the supply currents in the good and faulty circuits willalso be very different. Further, specific tests can be applied so as toimprove fault coverage. Power monitoring is verified using simulation, andalso experimentally, for example circuits.     

Numerical Simulation of Independent Advance of Ore Breaking in the Non-pillar Sublevel Caving Method

The mechanism of stress generation and propagation by detonation loading in five separate independent advance of ore breaking patterns is discussed in the paper. An elastic numerical model was developed using AN- SYS/LS-DYNA 3D Nonlinear Dynamic Finite Element Software. In this package ANSYS is the preprocessor and LS-DYNA is the postprocessor. Numerical models in the paper to actual were l：10 and the element mesh was dissected in scanning mode utilizing the symmetry characteristics of the numerical model. Five different advance rates were studied. Parameters, such as the time required to maximum stress, the action time of the available stress, the maximum velocity of the nodes, the stress penetration time, the magnitude of the stress peak and the time duration for high stress were numerically simulated. The 2.2 m advance appeared optimum from an analysis of the simulation results. The results from numerical simulation have been validated by tests with physical models.     

气门用4Cr9Si2钢调质工艺研究

采用正交试验 ,研究了 4Cr9Si2钢的淬火温度、回火温度与组织、硬度间的关系 ,得出了最佳的工艺参数 (10 10℃淬火 ,6 0 0℃回火 )。实际生产表明 ,采用此工艺后 ,断裂现象基本消除 ,气门的热处理质量有了明显提高。