新型电潜螺杆泵减速器齿轮干涉问题的研究

为保证齿轮设计的正确性，介绍了新型电潜螺杆泵减速器齿轮传动中存在的各种干涉现象及产生的原因和避免的条件，通过分析计算给出了避免各种干涉的变位系数的取值范围和措施。     

锗酸铋（Bi4Ge3O12）单晶热物理性质的研究

本文用不同的测试技术和方法测定了锗酸铋(BGO)单晶的比热(300～800K)热膨胀系数(100～1100K)和导温系数(140～700K),进而导出了 BGO 单晶不同温度下的导热系数、定容比热、德拜温度和格虑内森数。本文还对 BGO 单晶热物理性质的变化规律作了理论解释。     

螺旋管簧的可靠性优化设计

讨论了螺旋管簧的可靠性优化设计问题。在基本随机变量的概率特性已知的情况下，采用二阶矩法和可靠性优化设计方法对螺旋管簧进行了可靠性优化设计。通过计算机程序可以直接实现螺旋管簧的可靠性优化设计，迅速准确地得到螺旋管簧的可靠性优化设计信息。     

固液相变蓄能的数学模型和自然对流换热系数的实验研究

引入自然对流换热系数 ,将固液蓄能数学模型简化为仅用能量方程加以描述。并通过实验测得相变过程的实际温度场 ,证明了自然对流固液相变换热的影响不可忽略 ,验证了固液相变界面移动速率随自然对流换热系数的增大而增大的定性关系     

MODELING LIQUID MASS TRANSFER IN HIGEE SEPARATION PROCESS

Correspondence concerning this paper should be addressed to Professor Richard S.H. Mah. Hsien-Hsin Tung is now affiliated with Department of Chemical Engineering, California Institute of Technology

Penetration theory is used to describe the liquid mass transfer in Higee separation process. Within a possible range of effective areas, it is shown that the predicted mass transfer coefficients are in reasonable agreement with the estimated mass transfer coefficients. The estimated coefficients were calculated from the experimental data and the possible effective areas. Hence it is concluded the penetration theory is generally applicable to describe liquid mass transfer in Higee separation process. The comparison also suggests that liquid mixing at the junctions of packing materials may be more complete in Higee process than in traditional process.     

ˮ�ཬ������������Ƽ�����Ľ�������о�

解决注水泥作业的防气窜问题，是提高固井质量，保护油气层的关键技术。现有预测和防止水泥浆气管理的方法虽然较多，但应用于现场却有一定困难，主要表现在所考虑的因素比较单一，有些高温、高压下的水泥浆性能参数难以测定。文章在分析国内外预测和防止气窜方法的基础上，应用水泥浆浆体在环空的组成，GFP系数、水泥浆稠度阻力系数（A）及多凝水泥和环空加压等措施，拟定出一套提高水泥浆顶替效率，保证水泥浆动态和静态过程压力平衡关系的具体设计方法。     

电容位移法精确测量磁性薄膜的磁致伸缩系数

介绍了一种精确测量磁性薄膜磁致伸缩系数方法－电容位移法，并自行研制组装了一套测量装置，通过误差分析，仪器的精确标定，对稀土－铁超磁致伸缩薄膜的磁致伸缩系数进行了测量，获得满意的结果。     

热释电系数的测量方法

描述热释电系数的两种测量方法。其一为电荷积分法，测试系统简单，测量数据准确，且能满足零电场条件下的测量。其二为动态电流法，采用调制热源技术，研究在特定温度条件下热释电材料的动态热释电响应。     

高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.