人群头发元素分布及某些特征研究

本文介绍用堆中子活化分析法测定人群头发中I、Br、Mg、Mn、Cu、Na、V、Cl、Al、Ca、S等11种元素。研究人发中元素分布特征、相关性特征、性别年令分布特征。方法学中还从法庭科学应用角度介绍同一性识别中差异率和重合几率的双判据方法。     

Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

FORMATION OF MANGANESE SILICIDE THIN FILMS BY SOLID PHASE REACTION

1. IntroductionThe transition metal silicides have attraeted much attention because of their potentialapplicatiOIl in very large scale integration (VLSI) de.ice[1]. Near-noble metal silicides canbe used as Schottky al1d ohn1ic col1tacts in silicon-based d…     

电感电容损耗电阻的讨论

通过对电容电感阻抗的测量，发现实验值偏离理论值。定性地分析了误差的来源，得出的结论是电感电容内部的损耗电阻随着频率的变化而变化，变化方向相反而并非相同。     

提高高铬白口铸铁磨球冲击抗力的技术关键

当高铬白口铸铁含铬量为18%～28%,Cr/C值是8￣9,铸铁的显微组织是回火马氏体 少量残余奥氏体(<5%) M7C3碳化物,则磨球具有高的冲击韧性和断裂韧性K1C,具有高的冲击抗力,表现出低的冲击剥落量。     

Diffusion of additives and plasticizers in poly(vinyl chloride): 4. A programmed temperature technique for the determination of the diffusion parameters of three dialkylphthalates

A programmed temperature technique has been developed for the measurement of the self-diffusion coefficients of additives in polymers. This has been applied to the diffusion of three dialkylphthalate plasticizers in poly(vinyl chloride). Values of the self-diffusion coefficients and the calculated activation energies obtained in this way have been compared with values previously obtained from measurements at constant temperature. It has been shown that the programmed temperature technique gives a very rapid method for the estimation of the activation energy of self-diffusion.     

The role of the surface free energy in the selection of a suitable excipient in the course of a wet-granulation method

Pellets containing metronidazole were produced in a centrifugal granulator, with hydroxypropylcellulose (Klucel LF®) as binding agent, and corn starch, microcrystalline cellulose (Vivapur 101®) and lactose as excipients. The wettability of the pharmaceutical powders was assessed by means of contact angle measurements, and the dispersive and polar surface energies were determined. The spreading coefficients, the work of adhesion and the work of cohesion were calculated and correlated with the pellet properties (friability, bulk and tapped density, and porosity). The aim was to investigate the role of the surface free energy of one- and two-component powder compositions in pellet production. The interactions between the particles were found to be connected with the measured pellet parameters. It was concluded that, in the course of the growth of the pellets, the particle sizes of the pharmaceutical powders and the interactions between them are important. If the work of cohesion of the binder is lower than the work of cohesion of the substrate and the work of adhesion, then the optimal amount of the binding agent is that which coats the particles uniformly in minimal quantity and in continuous layer.     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

利用C++Builder对处理ESCR数据方法的改进

介绍一种利用C＋＋Builder编程工具自动处理聚乙烯环境应力开裂(ESCR)试验数据的方法。此方法利用计算机简化试验数据的处理过程,消除标准试验方法中作图法所引入的人为误差,并可以大幅度缩短试验时间。