Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and aqueous solution behaviors of sodium sulfonate‐terminated dendritic poly(ester‐amine)

Sodium sulfonate‐terminated dendritic poly(ester‐amine) (SPEA) was synthesized by sulfonation of acrylic double bond‐terminated dendritic poly(ester‐amine) (APEA) with sodium hydrogen sulfite (NaHSO₃) in mixture of diglycol and 2‐butanone under normal pressure. The structure of SPEA was characterized by IR, ¹H‐NMR, and elemental analysis. SPEA was water‐soluble. 1.0–40.0% (mass) SPEA aqueous solutions appeared as dilatant fluid. When pH value varied from 1.5 to 12.0, the viscosity of 1–5% (mass) SPEA aqueous solutions changed very small, and the electric conductivity almost kept stable within pH 3.0–10.0. The relationship between the viscosity and the concentration of SPEA water solutions was similar to that of NaCl water solutions. The surface tension of SPEA water solutions was lower than that of polyethylene glycol 2000 water solutions with the same concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of monodisperse poly(vinyl alcohol) microspheres by heterogeneous surface saponification and iodine complex formation

Monodisperse poly(vinyl acetate) (PVAc) microspheres with high molecular weight obtained by suspension polymerization of vinyl acetate were saponified in alkaline aqueous solution to keep their spherical structure. The saponification was restricted on the surface of the PVAc microspheres and obtained particles had skin/core structure. Various poly(vinyl alcohol) (PVA) microspheres with different diameters and degrees of saponification (DSs) were obtained. The conversion of PVAc to PVA during the heterogeneous surface saponification time were examined by nuclear magnetic resonance spectroscopy and after 72 h hydrogel type PVA microspheres completely saponified were obtained. The crystal melting temperatures of the microspheres obtained by the saponification were measured a constant value of 238°C irrespective of varying DS, and the peaks became enlarged as reaction time. Iodine complexes were formed in saponified microspheres with DS of 41% and 99% by immersing them in I₂/KI aqueous solution and decomposed by the reduction of I₂ in the complexes to 2I^? using sodium sulfite to confirm whether the skin formed through the saponification was composed of PVA with high VA content. Obviously, characteristic blue color developments owing to I₅^?‐PVA complexes were observed in both saponified regions and a red in the PVAc core. Consequently, it was concluded that the PVA skins formed by heterogeneous surface saponification had high DSs. Such complexes endowed polymeric microspheres a good radiopacity which would be useful in clinical treatment of vascular diseases and were examined by X‐ray irradiation image. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and structural characterization of methacrylic acid/octadecyl acrylate‐graft‐poly(methylhydrosiloxane) by hydrosilylation

Methylmethacrylate (MMA) and octadecyl acrylate (OA) were grafted to poly(methylhydrosiloxane) (PMHS) by hydrosilylation, respectively, with hexachloroplatinic acid as catalyst, and the former was further hydrolyzed to prepare methacrylic acid (MAA)‐graft‐PMHS under the alkaline condition. Through orthogonal experiment, main factors affecting the graft reaction between OA and PMHS were discussed and arranged in a decreasing order according to their abilities of the effect on the hydrosilylation of OA with PMHS: catalyst dosage, reaction temperature, reaction time, material ratio, and solvent dosage. It was found that the hydrosilylation of OA with PMHS was easier to that of MMA with PMHS. Under optimal conditions, the grafting ratios of MMA with PMHS and OA with PMHS reached about 90 and 95%, respectively. FTIR and ¹H NMR spectra indicated that the hydrosilylation reactions followed the Markovnikov's rule and played a strong preference toward β‐1,2‐addition. The test of contact angle indicated that surface energy of a system was mainly dependent on the polar groups. The surface energy of OA‐graft‐PMHS (35.07 mN/m) was similar to those of PMHS (35.62 mN/m) and polyoctadecyl acrylate (36.57 mN/m), and lower than that of MAA‐graft‐PMHS (43.50 mN/m). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

A study on dynamic friction of different spun yarns

This article presents the results from a study of yarn-to-yarn (YY) and yarn-to-metal (YM) frictions conducted on ring, rotor, air-jet, and open-end friction (OE friction) spun yarns at different relative speeds and input tensions. The results indicate that the behavior of frictions for YY is different than that of YM. In case of YY friction, OE friction yarn shows maximum friction followed by rotor, air-jet, and ring spun yarns; however, a reverse order is noticed for YM friction. The relative speed and input tension have significant influence on the frictional behavior of spun yarns. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.     

Response surface methodology applied for Orange II photocatalytic degradation in TiO2 aqueous suspensions

BACKGROUND: Heterogeneous photocatalysis is influenced by a number of parameters involving synergistic effects; hence, an experimental strategy design that considers interactions between the main variables is needed. The response surface methodology was applied for the investigation of photodegradation of 20 mg L^?1 Orange II in aqueous solutions and for optimization of color removal efficiency. Preliminary studies were performed to identify the parameters to be selected for optimization. RESULTS: The input variables considered for experimental design were: solution initial pH, oxidizing agent (H₂O₂) initial concentration and UV‐A irradiation time. The multivariate experimental design allowed the development of a quadratic response surface model to be used for the prediction of color removal efficiency over the full range of the experimental region. Under the optimum conditions established in the region of experimentation (pH = 6.9, [H₂O₂]₀ = 183 mg L^?1 and t = 32 min), a 100% color removal efficiency was obtained in experiments. CONCLUSIONS: It was found that the variables considered have important effects on color removal efficiency. The results demonstrate that the use of experimental design strategy is indispensable for successful investigation and adequate modeling of the process because the interdependence of the reaction parameters cannot be neglected. Copyright © 2008 Society of Chemical Industry     

Surface tension as a limiting factor for aerobic n-alkane biodegradation

A new mathematical model for n-alkane biodegradation in crude oil, heavy oil and paraffinic mixtures is described. The pattern of n-alkane degradation as a function of the inverse of hydrocarbon chain length reported in this paper can be considered as general behaviour for many aerobic n-alkane biodegradation processes. A new interpretation of n-alkane biodegradation as a function of surface tension, is given. A mathematical expression was obtained starting from the degradation values of n-alkane and relative surface tension, which is a parameter independent of fermentation conditions. An interesting parameter, b, was identified which represented the accelerating conversion factor for n-alkane biodegradation. The findings suggested that the n-alkane biodegradation. The findings suggested that he n-alkane biodegradation rate may be affected by the fermentation condition (agitation, aeration, etc.) and by the strain of microorganism, while the behaviour pattern of n-alkane degradation was essentially linked to the substrate characteristics (molecular structure, molecular weight and density).     

纤维表面处理对植物纤维增强水泥的物理力学性能影响

植物纤维增强水泥的力学性能具有湿敏感性，随湿度增加弯曲强度下降幅度较大。本文工作采用的几种浸渍处理纤维表面的方法，有效地改善了这种状况，其中一种经处理的纤维增强水泥较没有处理的对比试样在饱水状态下的弯曲强度提高了67％，气干状态提高了18％，缩小了二者间的差距。