懒蚂蚁效应

什么是懒蚂蚁效应?日本北海道大学进化生物研究小组对三个分别由30只蚂蚁组成的黑蚁群的活动进行了观察。结果发现,大部分蚂蚁都很勤快地寻找、搬运食物、少数蚂蚁却整日无所事事、东张西望,人们把这少数蚂蚁叫做“懒蚂蚁”。     

对硝基苯偶氮2-羟基萘-3-甲酰烷基胺系聚丙烯纤维用红色染料的合成及应用

本文将2,3-酸在甲苯溶剂中用氯化亚砜酰氯化合成2-羟基萘-3-甲酰氯,将其分别和正丁胺、正辛胺、正十二胺和正十八胺反应制得4种不同碳链长度的2-羟基萘-3-甲酰烷基胺,用对硝基苯胺重氮盐与其偶合分别制得了对硝基苯偶氮2-羟基萘-3-甲酰正丁胺、对硝基苯偶氮2-羟基萘-3-甲酰正辛胺、对硝基苯偶氮2-羟基萘-3-甲酰正十二胺和对硝基苯偶氮2-羟基萘-3-甲酰正十八胺系聚丙烯纤维用红色染料。熔点分别为189.8℃、96.2℃、115.8℃和108.1℃;热分解点分别为273.1℃、216.0℃、258.0℃和221.0℃;最大吸收波长分别为515.8nm、516.8nm、513.6nm和514.2nm。在染色条件下,4支染料在聚丙烯纤维上的上染率分别37.6％、41.8％、42.4％和44.7％。     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

单线对高比特率数字用户线(SHDSL)简介

介绍单线对高比特率数字用户线（SHDSL）设备的应用环境、参考模型、接口类型、功能、传输性能等等。     

SO_3磺化法合成PNTS新工艺的研究

本文采用正交设计及方差分析法,确定了 SO_3磺化法合成 PNTS 新工艺的最佳工艺条件;并从技术及经济方面将新工艺同国内现有的生产老工艺进行了分析对比。     

RS码频域纠错编码在激光对潜通信信道中的实现方法

介绍了信道编码在激光对潜通信系统中的重要作用，介绍了频域编译ＲＳ码的基本方法，并给出了脉冲位置调制信道的ＲＳ码频域编译码的计算机模拟方法和结果。     

超声钻孔对测法探测大坝裂缝深度

本文通过介绍超声钻孔对测法探测大坝裂缝深度，说明超声钻孔对测法检测混凝土大坝裂缝深度的有效性。     

采用信息融合技术的IR／MMW复合导引头的目标跟踪

从误差测量环节入手，基于IR／MMW双模结构，采用信息融合处理技术提高其估计跟踪精度，最终达到降低制导误差，提高武器性能的目的，仿真结果验证了该方法的有效性。