A Parameterization Method from Conic Spline Interpolation

Interpolating a set of planar points is a common problem in CAD. Most constructions of interpolation functions are based on the parameters at the sample points. Assigning parameters to all sample points is a vital step before constructing interpolation functions. The most widely used parameterization method is accumulative chord length parameterization. In this paper, we give out a better method based on the interpolation of conics. Based on this method, a sequence of fairer Hermite curves can be constructed.     

CoMoO4负载Mo-V-Cr-Bi氧化物催化剂上甲烷部分氧化的研究

研究了CoMoO4负载Mo-V-Cr-Bi氧化物催化剂上甲烷部分氧化反应,发现反应存在一转折温度,当反应温度低于此温度时,CO是主要产物,而部分氧化产物甲醇的选择性低于20%,而当反应温度高于此温度时,CO的选择性大大降低,而CO2的选择性大大升高,主要产物变为CO2,甲醇的选择性降为0。在O2完全反应的时候,总会有H2生成,特别当反应温度高于转折温度的时候,H2的生成量大大增加。     

核为︱x-s︱~(-1)ln︱x-s︱的强奇异积分的数值计算法

讨论了核为︱x-s︱~(-1)ln︱x-s︱的一种强奇异积分∫baln︱x-s︱/︱x-s︱f(xdx),给出了它的Hadamard有限部分积分的定义,并利用Lagrange线性插值构造了函数这类强奇异积分的数值算法,最后分析和讨论了算法的误差估计。     

一种高效的基于身份的部分盲签名方案*

提出了一个新的基于身份的部分盲签名方案,证明了所提方案的完整性、部分盲性和不可伪造性,并比较了所提方案与现有方案的计算代价,比较结果显示所提方案是目前效率较高的基于身份的部分盲签名方案。     

部分信息下的最优投资选择模型研究

在部分信息下研究了均值方差投资选择模型.投资者只能观察到风险资产的价格,漂移过程用一个高斯过程来刻画.本文的目的是使最终财富期望最大化,而使得最终财富的方差最小.本文模型中有一个债券及股票资产,在部分信息下推导出了最优策略及均值方差有效前沿.     

相干组束自成像腔腔型设计理论研究

为了更合理地设计光纤组束谐振腔,针对自成像共振腔,用傅里叶光学理论对其进行了分析,并讨论了3种关键元件——傅里叶透镜、滤波器与输出镜的选取方法;提出了用MATLAB进行数值模拟进而得出空间滤波器透过率函数的计算方法.并以2个半径为55 mm且相距为240 mm的圆形光场为例,模拟了经过傅里叶变换后频谱面上的振幅分布和相位分布情况,通过比较相位,得到了两光场的同相位分布图像.同时,根据矩阵传输理论对腔体进行了分析,得到了自成像无源共振腔稳定振荡的必要条件,及振荡光光纤耦合效率最高的条件.     

Nonlinear behavior of concrete beams with hybrid FRP and stainless steel reinforcements

The full-range behavior of partially bonded, together with partially prestressed concrete beams containing fiber reinforced polymer (FRP) tendons and stainless steel reinforcing bars was simulated using a simplified theoretical model. The model assumes that a section in the beam has a trilinear moment—curvature relationship characterized by three particular points, initial cracking of concrete, yielding of non-prestressed steel, and crushing of concrete or rupturing of prestressing tendons. Predictions from the model were compared with the limited available test data, and a reasonable agreement was obtained. A detailed parametric study of the behavior of the prestressed concrete beams with hybrid FRP and stainless steel reinforcements was conducted. It can be concluded that the deformability of the beam can be enhanced by increasing the ultimate compressive strain of concrete, unbonded length of tendon, percentage of compressive reinforcement and partial prestress ratio, and decreasing the effective prestress in tendons, and increasing in ultimate compressive strain of concrete is the most efficient one. The deformability of the beam is almost directly proportional to the concrete ultimate strain provided the failure mode is concrete crushing, even though the concrete ultimate strain has less influence on the load-carrying capacity. Foundation item: Project (50478502) supported by the National Natural Science Foundation of China     

非线性部分最小二乘方法的研究与应用

该文将部分最小二乘算法与径向基函数神经网络相结合,给出了一种非线性部分最小二乘建模方法,可以更加有效地处理过程非线性和数据共线性等复杂特性,提高模型的精度和推广能力。该方法在确定径向基函数神经网络的隐节点时,采用了一种改进型的k-均值聚类算法来自动确定最优的聚类区数。对煤气化炉合成气组分浓度软测量建模的应用结果表明,采用该方法建立的软测量模型在模型精度和推广能力等方面明显优于二次型多项式部分最小二乘方法建立的模型,并且计算精度满足工业生产的实际要求。     

H型钢部分包裹混凝土组合短柱偏心受力性能研究

对6根焊接普通H型钢部分包裹混凝土组合短柱进行了偏心受压试验的研究,主要考虑含钢率、翼缘宽厚比等因素.试验结果表明,钢与混凝土能够很好地协同工作,达到最大荷载前,翼缘没有发生局部屈曲.这种组合结构柱最终的破坏模式为混凝土压碎,横向系杆间翼缘发生局部屈曲.