Iterative equalization combining algorithm in intersymbol interference channel

To realize joint optimization of spatial diversity and equalization combining in the intersymbol interference (ISI) channel, an iterative equalization combining algorithm is proposed. The proposed algorithm uses the coefficients of Turbo equalization to calculate the combination weights without estimating the signal to noise ratio in each diversity branch. The equalized symbols from different diversity branches are combined, and the extrinsic information output from the decoder is fed back to the equalizers, so as to exchange soft information between the equalizers and the decoder. The performance of the proposed algorithm is analyzed using the extrinsic information transfer (EXIT) chart and verified by simulations. Results show that our approach fully exploits time domain information from the multipath channel and spatial domain information from multi receiving antennas, which efficiently improve the performance of the receiver in the severe ISI channel.     

Influence of ZrB2 hard ceramic reinforcement on mechanical and wear properties of aluminum

In this work, the effect of ZrB₂ (0, 5, 10 and 20?vol%) ceramic reinforcement on densification, structure, and properties of mechanically alloyed Al was investigated. The milling of Al-ZrB₂ powder compositions resulted in formation of agglomerates with varied size. In particular, the size of agglomerates was reduced considerably with increased addition of ZrB₂ to Al. Interestingly, the densification of hot pressed Al increased from 96.06% to 99.22% with ZrB₂ addition. The reduction of agglomerates size was attributed to the enhanced densification of Al-ZrB₂ composites. Pure Al showed relatively low hardness (0.94?GPa) and it was improved to 1.78?GPa with the addition of 20?vol% ZrB₂. The mechanical properties have significantly been improved for Al-ZrB₂ composites. Especially Al - 20?vol% ZrB₂ possessed a very high yield strength (529?MPa), compressive strength (630?MPa) and compressive strain of 19.25%. Realization of such a good combination of mechanical properties is the highest ever reported for Al composites so far in the literature. The coefficient of friction (COF) of Al-ZrB₂ varied narrowly between 0.33 and 0.40 after dry sliding wear against steel disc. The wear rate of Al-ZrB₂ composites was within mild wear regime and varied between 98.88?×?10^?6 and 34.66?×?10^?6 mm³/Nm. Among all the compositions, Al - 20?vol% ZrB₂ composite exhibited the lowest wear rate and high wear rate was noted for pure Al. Mild abrasion, tribo-oxidation, third body wear (wear debris) and delamination were the major material removal mechanisms for Al-ZrB₂ composites. Overall the hardness, strength and wear resistance of Al - 20?vol% ZrB₂ composite was improved by 84.3%, 84.3% and 64.2%, respectively when compared to pure Al.     

Barium titanate‐based nanodielectrics of two chemically recyclable thermosets

In this work was investigated the effect of the addition of barium titanate (BaTiO₃) on electrical properties of two chemically recyclable thermosets, polyhemiaminal (PHA) and polyhexahydro‐s‐triazine (PHT), both fabricated from 4,4′‐oxydianiline (ODA), an ether derivative of aniline and paraformaldehyde. Thermal and mechanical properties as well as chemical recyclability of the two polymers and their nanocomposites/nanodielectrics were also investigated. In addition, a quantitative analysis was conducted of the nanoparticle dispersion in the PHA‐/PHT‐based BaTiO₃‐containing nanocomposites using transmission electron microscopy imaging and the nearest‐neighbor distance index and this index was used to analyze the investigated properties in connection with the proper mechanisms. Regarding the electrical properties for both neat polymers, conductivity values of the order of 10^?8 S m^?1 at 100 Hz were observed and dielectric constant values close to 2.80 for both polymers at 1 kHz. The addition of 0.5 wt% of BaTiO₃ ferroelectric nanoparticles increased by about 44% the dielectric constant (1 kHz) and conductivity (10² Hz) of the PHA‐based nanocomposite. PHA and PHT exhibited glass transition temperature (T_g) values in the range 125–180 °C. An increase of 7 °C in T_g was observed after the incorporation of 0.5 wt% of BaTiO₃ into PHA. Concerning the mechanical properties, values in the range 4.00–4.45 GPa for reduced modulus and 0.30–0.43 GPa for nanohardness for PHA and PHT polymers were observed. Independently of filler content or polymer matrix, both mechanical properties were enhanced after the addition of BaTiO₃. The chemical recycling of PHA/PHT and all nanocomposites in the initial ODA reagent after sulfuric acid treatment was successfully characterized using the NMR and Fourier transform infrared spectroscopic techniques. © 2018 Society of Chemical Industry     

Dielectric,ferroelectric, and piezoelectric properties of lead-free Ba0.95Ca0.05Ti1-xZrxO3 ceramics

Abstract

Ba_0.95Ca_0.05Ti_1-xZr_xO₃ (BCTZO) ceramics were prepared by a solid state reaction method. The samples were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and X-ray absorption near edge structure (XANES). The ceramics exhibit a pure perovskite structure. The average grain size gradually decreases with increasing Zr concentration. XANES results indicate that the intensities of pre-edge peaks dropped with increasing Zr concentration. The BCTZO ceramic of x?=?0.05 has the optimum electrical properties with the maximum dielectric constant (ε'_m), remanent polarization (2P_r), coercive electric field (2E_c) and piezoelectric charge constant (d₃₃) of 7,244, 12.54 (μC/cm²), 5.29 (kV/cm) and 288 (pC/N), respectively.     

Viability of intertwined supply networks: extending the supply chain resilience angles towards survivability. A position paper motivated by COVID-19 outbreak

An intertwined supply network (ISN) is an entirety of interconnected supply chains (SC) which, in their integrity secure the provision of society and markets with goods and services. The ISNs are open systems with structural dynamics since the firms may exhibit multiple behaviours by changing the buyer-supplier roles in interconnected or even competing SCs. From the positions of resilience, the ISNs as a whole provide services to society (e.g. food service, mobility service or communication service) which are required to ensure a long-term survival. The analysis of survivability at the level of ISN requires a consideration at a large scale as resilience of individual SCs. The recent example of coronavirus COVID-19 outbreak clearly shows the necessity of this new perspective. Our study introduces a new angle in SC resilience research when a resistance to extraordinary disruptions needs to be considered at the scale of viability. We elaborate on the integrity of the ISN and viability. The contribution of our position study lies in a conceptualisation of a novel decision-making environment of ISN viability. We illustrate the viability formation through a dynamic game-theoretic modelling of a biological system that resembles the ISN. We discuss some future research areas.     

基于RFID标签阵列的睡眠期间呼吸量连续监测系统

睡眠期间连续且准确的呼吸量监测有助于推断用户的睡眠阶段以及提供一些慢性疾病的线索。现有工作主要针对呼吸频率进行感知和监测,缺乏对呼吸量进行连续监测的手段。针对上述问题提出了一种基于商用无线射频识别(RFID)标签的无线感知用户睡眠期间呼吸量的系统——RF-SLEEP。RF-SLEEP通过阅读器连续收集附着在胸部表面的标签阵列返回的相位值及时间戳数据,计算出呼吸引起的胸部不同点的位移量,基于广义回归神经网络(GRNN)构建胸部不同点的位移量与呼吸量之间的关系模型,从而实现对用户睡眠期间呼吸量的评估。RF-SLEEP通过在用户肩膀处附着双参考标签,消除用户睡眠期间翻转身体对胸部位移计算造成的误差。实验结果表明,RFSLEEP对不同用户睡眠期间的呼吸量连续监测的平均精确度为92.49%。     

嵌入式实时操作系统内核混合代码的自动化验证框架

"如何构造高可信的软件系统"已成为学术界和工业界的研究热点.操作系统内核作为软件系统的基础组件，它的安全可靠是构造高可信软件系统的重要环节.为了确保操作系统内核的安全可靠，将形式化方法引入到操作系统内核验证中，提出了一个自动化验证操作系统内核的框架.该验证框架包括：（1）分别对C语言程序和混合语言程序（C语言和汇编语言）进行验证；（2）在混合语言程序验证中，为汇编程序建立抽象模型，并将C语言程序和抽象模型粘合形成基于C语言验证工具可接收的验证模型；（3）从规范中提取性质，基于该自动验证工具，对性质完成自动验证；（4）该框架不限于特定的硬件架构.成功地运用该验证框架对两种不同硬件平台的嵌入式实时操作系统内核μC/OS-II进行了验证.结果显示：利用该框架在对两个不同的硬件平台上内核验证时，框架的可重复利用率很高，高达到88%，虽然其抽象模型需要根据不同的硬件平台进行重构.在对基于这两种平台的操作系统内核验证中，分别发现了10~12处缺陷.其中，在ARM平台上两处与硬件相关的问题被发现.实验表明，该方法对不同硬件平台的同一个操作系统分析验证具有一定的通用性.     

Broad-Spectral-Range Sustainability and Controllable Excitation of Hyperbolic Phonon Polaritons in α-MoO3

Hyperbolic phonon polaritons (HPhPs) in orthorhombic-phase molybdenum trioxide (α-MoO₃) show in-plane hyperbolicity, great wavelength compression, and ultralong lifetime, therefore holding great potential in nanophotonic applications. However, its polaritonic response in the far-infrared (FIR) range remains unexplored due to challenges in experimental characterization. Here, monochromated electron energy loss spectroscopy (EELS) in a scanning transmission electron microscope (STEM) is used to probe HPhPs in α-MoO₃ in both mid-infrared (MIR) and FIR frequencies and correlate their behaviors with microstructures and orientations. It is found that low structural symmetry leads to various phonon modes and multiple Reststrahlen bands (RBs) over a broad spectral range (over 70 meV) and in different directions (55–63 meV and 119–125 meV along the b-axis, 68–106 meV along the c-axis, and 101–121 meV along the a-axis). These HPhPs can be selectively excited by controlling the direction of swift electrons. These findings provide new opportunities in nanophotonic and optoelectronic applications, such as directed light propagation, hyperlenses, and heat transfer.     

Alternatives for improving energy security in Cape Verde

The lack of consensus on the meaning of energy security and how it should be measured hinders the evaluation of alternatives for improving the Cape Verdean energy sector. The objective of the paper is to develop an energy security index adjusted to the country's context. The methods used are the multi-criteria analysis and the Delphi survey. Different alternatives to improve energy security are assessed: electrically interconnect Cape Verde's islands, increase the share of renewable energy, and a combination of the previous alternatives. The results of our analysis indicate that increasing renewable energy is the optimal alternative for Cape Verde.